Configure Armfly RS485 LoRa I/O Modules
$10-30 USD
Posted 1 minute ago
•
Ends in 6 days
$10-30 USD
Paid on delivery
Title: Configure and pair two wireless RS485 / LoRa 433 MHz analog I/O modules (RC402 + RC302) I need someone experienced with Modbus RTU / RS485 to pair two wireless analog I/O modules made by Armfly. I will ship them to you and you send them back configured. - RC402-7K: 0-10 V analog input (transmitter) - RC302-7K: 0-10 V analog output (receiver) Goal: the 0-10 V signal on channel 1 of the RC402 must be reproduced on channel 1 of the RC302, over radio. According to the manual, this is done with the manufacturer's PC software (Chinese interface): - RC402 in work mode 2, mini-program 17 (RC402 → RC302), with P1 = RC302 address and P2 = 300 ms. - RC402 channel 1 set as 0-10 V voltage input. - Same radio channel and air data rate on both modules (channel 24, 434 MHz, 19.2K). Requirements: - You must have a USB-RS485 adapter, a 12-24 V power supply and a multimeter. Deliverables: - Both modules shipped back, paired and tested. - A photo or short video of the multimeter on the RC302 output following the RC402 input. - A list of the final configured values. I will send the modules with their antennas, the full PDF manual and a ready-made step-by-step guide. I pay outbound shipping; please state in your proposal which country you are in and whether your price includes return shipping. Please tell me whether you have worked with Modbus/LoRa modules and with Chinese-language configuration software.
Project ID: 40820749
About the project
4 proposals
Open for bidding
Remote project
Active 24 secs ago
Place your bid
Bid amount Email addressBenefits of bidding on Freelancer
Set your budget and timeframe
It's free to sign up and bid on jobs
4 freelancers are bidding on average $21 USD for this job


Hello, My 10+ years in industrial electronics, automation, embedded systems, sensors, and data acquisition directly match the practical testing required for your Armfly RC402/RC302 setup. I can configure the 0-10 V input/output relationship, work with the specified RS485/Modbus environment, and verify the transmitted signal using suitable electrical test equipment. My background includes wireless communication, LoRaWAN, analog and digital electronics, UART-based systems, hardware troubleshooting, commissioning, and industrial control systems. This gives me the hands-on experience needed to handle the Chinese configuration software, apply the required radio and operating parameters, and confirm that RC302 channel 1 follows RC402 channel 1 correctly. I can provide the requested final configuration values together with a photo or short video of the multimeter test. I am located in [country]. I can provide a USB-RS485 adapter, 12-24 V power supply, and multimeter for the work; return shipping would be [included/not included] in my price. I would be glad to configure, test, and return both modules. Thanks!


Hello, My 15+ years as an Electronic Hardware and Firmware Engineer make me well suited to configure and test your Armfly RC402/RC302 wireless I/O pair. My background in embedded systems, industrial automation, and communication protocols, including UART and related serial interfaces, supports the precise setup required for RS485/Modbus RTU and reliable analog signal transfer. I can work with the supplied manual and Chinese configuration software to apply the specified work mode, mini-program, addresses, timing, radio channel, air data rate, and 0-10 V channel settings. My electronics and signal-processing experience also allows me to verify that the RC302 output follows the RC402 input using the required power supply, USB-RS485 adapter, and multimeter, then provide the configured values together with test photo/video evidence. I am ready to handle the configuration, pairing, and functional testing carefully before returning both modules. My location is [country], and return shipping [is/is not] included in my price. Thanks!


Hello, My embedded systems and wireless communication background is well matched to configuring and testing your Armfly RC402/RC302 pair. I work with LoRa-based systems, electronics, embedded hardware and testing, and I can use the supplied manual and guide to set the Modbus/RS485 parameters, radio settings, work mode and mini-program accurately. I can provide the required USB-RS485 adapter, 12-24 V power supply and multimeter for configuration and verification. My electronics and microcontroller experience supports careful checking of the 0-10 V input/output path, including confirming that the RC302 channel 1 output follows the RC402 channel 1 input. I can also document the final values and provide the requested photo or short test video. I can work with the Chinese-language configuration software using the provided documentation; my profile does not specifically claim prior use of Armfly’s software. I am based in [country] and would clearly state whether return shipping is included in my price. Choose me for a careful, test-focused configuration of both modules. Thanks!


Hi there, I’m Vadym, Electronics Engineer (Embedded & Power) with 10+ years configuring wireless I/O and RS485/Modbus RTU systems. I can reliably pair your Armfly RC402 (0-10 V input) and RC302 (0-10 V output) so channel 1 is reproduced over LoRa exactly as your guide specifies (work mode 2, mini-program 17, matching radio channel/air data rate). With the USB-RS485 adapter, 12-24 V supply, and a multimeter, I’ll configure both modules, verify the 0-10 V transfer on channel 1, and return them paired and tested. You’ll also receive a photo/video showing the multimeter output plus a clear list of the final configured values. Please share your country and confirm whether my proposed price includes return shipping. Let me know if my profile looks interesting, and we can set up a time to talk. Best regards, Vadym P.-
内容来自 Freelancer News,版权归原作者所有。
阅读原文 ↗