Hardware / Embedded Electronics Engineer — Automotive ECU Bench Bring-Up & Boot-Entry

₹12500-37500 INR

Posted half a minute ago

•

Ends in 6 days

₹12500-37500 INR

Paid on delivery

About the role: Automotive R&D project at Brookwoods. We handle the software and protocol side in-house — what we need is hardware expertise to physically bring an Engine Control Unit (ECU) into bench communication. The remaining gap is entirely at the electrical level: the power sequencing, signal conditioning, line interfacing, and precise timing that get the ECU into its boot/communication mode so it responds. You own the hardware; we drive the protocol on top of it. Scope of work (hardware-led) : Design and build the bench interface hardware connecting our controller to the ECU’s lines — correct level-shifting, line transceivers, and protection for mixed-voltage single-wire (K-line-style, 12 V) and low-voltage signals. Instrument and capture the physical initialization of a reference setup (power rails, clock/sync lines, serial line) on a logic analyzer + oscilloscope, on one common timebase. Determine the ECU’s boot-mode electrical entry conditions — reset/boot pin states, voltage levels, synchronous signaling, and power-up timing relative to the serial init. Build the power-sequencing + signal-timing hardware (MCU — STM32/Arduino — or FPGA-driven) that reproduces those conditions and reliably brings the ECU into communication so it issues its handshake. Deliver a working, documented hardware rig + wiring + any MCU/FPGA timing firmware; we integrate our protocol software. Must-have skills (hardware) - Strong hands-on analog/digital hardware bring-up and board-level debugging. - Level-shifting and line-transceiver design for single-wire 12 V automotive buses (K-line/LIN, open-drain) and mixed-voltage logic. - Precise signal-timing generation and power sequencing via MCU (STM32/Arduino) or FPGA. - Fluent with oscilloscope + logic analyzer; signal-integrity and timing debugging. - Understanding of automotive ECU / MCU boot-mode electrical entry — reset/boot pin conditions, synchronous boot/debug interfaces (BDM-class). Nice-to-have - PCB design; MPC5xx-class boot configuration; some protocol/firmware familiarity (we own the software, but context helps). Deliverables & acceptance (milestone-based) M1: time-aligned capture of the reference setup’s power + signal init, with the electrical entry conditions identified. M2: hardware rig that reliably drives the ECU into comms and captures its handshake response (live or recorded). M3: documented, reproducible hardware + timing firmware, handed over for our software to run on. We provide The ECU and bench setup, bench power, our controller / MCU / FPGA, logic analyzer, oscilloscope, transceivers — and the entire software/protocol side (we decode and drive it; you deliver the hardware that gets it talking). Full technical specifics shared after NDA. Engagement Freelance / contract, fixed-price — total project budget ₹15,000, milestone-based. Suggested split: M1 ₹3,000 · M2 ₹7,000 · M3 ₹5,000 (candidates may propose their own split). Remote OK with live screen-share / bench sessions; on-site in Bengaluru a plus. NDA required; all work product and IP assigned to Brookwoods Technologies. To apply A comparable hardware bench bring-up / boot-entry you’ve built (what it was, the interface circuit, the instruments you used). Your approach to this task in 3–5 bullets. Rate + rough timeline, and any shareable schematics/photos.

Project ID: 40820679

About the project

Open for bidding

Remote project

Active 57 yrs ago

Place your bid

Bid amount Email address

Benefits of bidding on Freelancer

Set your budget and timeframe

It's free to sign up and bid on jobs

内容来自 Freelancer News,版权归原作者所有。

阅读原文 ↗

把喜欢的内容,留在你的新标签页。

打开我的订阅