Fix ESP32 + PN532 Wiring

£20-250 GBP

Posted 1 minute ago

•

Ends in 6 days

£20-250 GBP

Paid on delivery

I need help fixing the wiring between an ESP32 and a PN532 NFC scanner. The scanner currently shows "No I2C device found." Requirements: - Correct SDA and SCL connections (currently SDA on 21, SCL on 22) - Ensure power wires are connected to the correct pins - PN532 must be detected after fix Ideal Skills: - Experience with ESP32 and PN532 - Knowledge of I2C wiring and troubleshooting

Project ID: 40819563

About the project

12 proposals

Open for bidding

Remote project

Active 6 secs ago

Place your bid

Bid amount Email address

Benefits of bidding on Freelancer

Set your budget and timeframe

It's free to sign up and bid on jobs

12 freelancers are bidding on average £208 GBP for this job

User Avatar
Flag of PAKISTAN

Hi, I understand that your ESP32 is not detecting the PN532 because the I2C wiring or power connection may be incorrect. I will check the SDA and SCL connections on GPIO 21 and 22, confirm the PN532 power and ground pins, verify the module’s I2C mode settings, and test the setup until the scanner is detected correctly. My Electronics and Microcontroller experience helps me trace the connection step by step, while my Electrical Engineering and Engineering knowledge will help avoid power or pin-related problems. I will also explain the final wiring clearly so you can repeat it safely. Is your PN532 board set to I2C mode, and could you share a clear photo of its pin labels and current ESP32 connections? Please start the chat and let’s discuss your current wiring, PN532 board version, and test results.

User Avatar
Flag of UKRAINE

Hello, Diagnosing ESP32 and PN532 I2C detection issues directly matches my 15+ years of experience in electronic engineering and embedded systems. I work with ESP32 platforms and I2C communication, so I can identify incorrect SDA/SCL routing, power connections, grounding, and interface configuration behind the “No I2C device found” message. My background in circuit design, embedded C/C++, and hardware troubleshooting allows me to address both the physical wiring and the firmware-side communication settings. I focus on reliable, practical fixes and can help ensure the PN532 is correctly powered, connected, and detected by the ESP32. Choose me to resolve this ESP32-PN532 wiring issue with careful electronics and I2C troubleshooting. Thanks!

User Avatar
Flag of UKRAINE

Hello, ESP32 embedded-systems experience combined with electronics and circuit-design expertise makes me well suited to resolve your PN532 “No I2C device found” issue. I can check the SDA/SCL mapping on GPIO 21 and 22, verify the PN532 power and ground connections, and identify wiring or configuration faults preventing detection. My background includes ESP32 firmware, embedded C/C++, sensor integration, hardware prototyping, and troubleshooting microcontroller-based circuits. This lets me assess both the physical connections and the I2C setup rather than treating the problem as wiring alone. I will focus on getting the PN532 correctly powered and recognized by the ESP32. Choose me to fix the connection and restore reliable communication between your ESP32 and PN532. Thanks!

User Avatar
Flag of TURKEY

Hi there, I see you're dealing with a wiring issue for the ESP32 and PN532 where it currently shows "No I2C device found." To resolve this, I would first ensure that the SDA and SCL are correctly connected (as you noted they're currently on pins 21 and 22). After verifying the connections, I’d check the power supply to ensure the PN532 is receiving adequate voltage. Once these steps are completed, we'll confirm if the PN532 is detected. Given my background with microcontrollers and troubleshooting I2C connections, I'm confident I can quickly address this issue. If you have any specifications regarding the power connections or additional details, feel free to share. I look forward to your response. Regards, Ali

User Avatar
Flag of PAKISTAN

Hello, I can help troubleshoot your ESP32 and PN532 NFC scanner connection and resolve the I2C detection issue. I will carefully verify the SDA and SCL connections on GPIO 21 and GPIO 22, check the correct power and ground pins, and confirm the PN532 module is configured for I2C mode. I will also guide you through checking wiring continuity, voltage levels, I2C addresses, and running an I2C scanner to identify the device. Once detected, I will verify communication and ensure the scanner works reliably with your ESP32. Please share your module model and current wiring photos so we can identify and fix the problem efficiently.

User Avatar
Flag of UKRAINE

Hi there, Which PN532 breakout board revision are you using, and is it powered from 3.3V or 5V? Do you want the fix limited to wiring only, or should I also verify the I2C pull-ups and scan code? The main issue looks like an I2C bus mismatch, not a software fault. A clean fix is to confirm SDA on GPIO 21 and SCL on GPIO 22, then trace VCC, GND, and any mode pins so the PN532 boots in I2C mode and responds to a bus scan. One risk is that some PN532 boards need the correct interface jumpers or pull-up level to work with the ESP32. If the module is wired right but still says no device found, I would check address selection, bus voltage, and shared ground before changing code. Can validate the wiring step by step, then test detection with a simple I2C scan and PN532 read. If needed, a small code adjustment can confirm the bus is alive and make the scanner visible on first boot. Best, Hlib

User Avatar
Flag of UKRAINE

Hi there, I can help fix the ESP32 ↔ PN532 NFC wiring so the scanner reliably detects the I2C device instead of showing “No I2C device found.” As an Electronics Engineer with 10+ years of embedded development and hardware troubleshooting, I’ll verify SDA/SCL wiring (and confirm I2C address/lines), ensure power/ground are on the correct pins, and validate the PN532 detection with a clean bring-up test. I’ll make the fix deterministic so you can read NFC consistently after the wiring correction. Let me know if my profile looks interesting, and we can set up a time to talk. Best regards, Vadym P.

User Avatar
Flag of UNITED STATES

Troubleshooting the “No I2C device found” error is a focused hardware-debugging task, and troubleshooting is the core skill I can apply to your ESP32 and PN532 setup. I can help verify the I2C connections, including SDA on GPIO 21 and SCL on GPIO 22, check the PN532 power and ground pins, and identify wiring or configuration issues preventing detection. My software engineering background also helps me validate the connection from the ESP32 side and distinguish wiring, power, and I2C communication problems efficiently. I will focus on getting the PN532 recognized reliably rather than only adjusting the scanner code. Choose me to troubleshoot the ESP32–PN532 connection and resolve the device detection issue.

User Avatar
Flag of UNITED STATES

Hi, I understand you need the ESP32-to-PN532 wiring corrected so the scanner is reliably detected over I2C instead of reporting “No I2C device found.” I can verify SDA GPIO21, SCL GPIO22, power, ground, PN532 interface-mode settings, and address detection while isolating wiring or configuration faults. I will deliver a corrected connection map and practical validation steps confirming the PN532 is detected; I hope we can talk together and start immediately. Best regards. Richard

内容来自 Freelancer News,版权归原作者所有。

阅读原文 ↗

把喜欢的内容,留在你的新标签页。

打开我的订阅