Affordable Multifamily Design and Engineering

$1000-10000 USD

Posted 1 minute ago

•

Ends in 6 days

$1000-10000 USD

Paid on delivery

Architectural Structural Engineering Fire Sprinker Design Mechanical Design Stamped plan set ready for submission to Sarasota, Florida building dept. I'm a contractor building a 36 unit affordable multifamily apartment building, consisting of two buildings each 18 units. The project will consist of 36 units, each unit the same floor plan (except for first floor units that may have to be modified for ADA). Each will be 2 bedroom, 2 bath, 750 square feet internal dimensions. The building will have six units per floor; with a total of 3 floors. No elevator- stairs on each end. The project will consist of two parallel buildings separated by a 20 foot courtyard. The first floor units may have to drop to 2 bed, 1 1/2 bath for ADA compliance, but I'd prefer not to do that unless required. I'm ok with demand water heaters to save space. Each unit will have a stacked washer/dryer. The building elevation will match an existing office building that is stucco over CMU with a mansard metal roof. I need a complete set of architectural drawings, structural engineering design and stamp, and mechanical for hvac (1.5 ton), etc., and fire sprinkler design. If you are not a Florida PE, possibly you have a relationship or relative who can stamp the plans. Building will be located in Sarasota County, 160mph wind D. I plan on using CMU with wood trusses between floors (with gybcrete), and wood trusses in ceiling. 9 foot ceilings. I've attached the blueprints for the existing office building (Phase 1). The duplicate office building was planned behind it (Phase 2). The slab was poured and three courses of block installed and then abandoned. I'm going to remove the existing slab and place the 36 units of apartments in that location. I provided the dwg files, survey, County plan comments, and a floor plan of a 750 square foot house I've built (surely can modify for ADA on first floor, make kitchen with island, move windows to front and back (not sides), etc. There is only so much you can do with 750 square feet. I think that design is 750 external and we can make it slightly bigger by using 750 internal dimensions. That may help, especially with ADA.

Project ID: 40818629

About the project

13 proposals

Open for bidding

Remote project

Active 10 secs ago

Place your bid

Bid amount Email address

Benefits of bidding on Freelancer

Set your budget and timeframe

It's free to sign up and bid on jobs

13 freelancers are bidding on average $3,860 USD for this job

User Avatar
Flag of EGYPT

Hello, My specialty is architectural 3D visualization, helping clients clearly see how buildings will look and function before construction. For your 36-unit multifamily project, I can transform the provided DWG files, survey, existing office elevations, and proposed floor plans into clear, professional architectural visualizations that communicate the two-building layout, courtyard, unit arrangement, CMU construction, stucco exterior, and mansard roof design. My team focuses on turning architectural concepts and blueprints into detailed visual presentations with attention to form, proportions, materials, and design consistency. This can help you evaluate how the repeated 2-bedroom units, stairs, façade, windows, and overall site arrangement work together before the final architectural, structural, mechanical, and sprinkler documents are prepared by appropriately licensed Florida professionals. I would be pleased to support the visual development and presentation of your apartment project with polished architectural renderings that reflect the intended design accurately. Thanks!

User Avatar
Flag of TURKEY

Hello; We are interested in your Affordable Multifamily Design and Engineering project. We are a professional team of expert architects from all over the world. Our team offers the highest quality and most effective projects with over 14 years of experience and works with a focus on 100% customer satisfaction. When you choose us, you will have a final delivery that exceeds your expectations. We look forward to working with you! Take a look at our past work on our portfolio: https://www.freelancer.com/u/worldarcpart Kind Regards WORLD ARCHITECTURE PARTNERS

User Avatar
Flag of UNITED STATES

Hello, My architectural understanding and structural engineering expertise are directly suited to developing a coordinated, buildable multifamily plan set for your Sarasota project. I create structural plans, framing layouts, load analysis, and detailed construction documents that integrate architectural layouts, mechanical systems, and site conditions. Your 36-unit design requires careful coordination between the repeated 2-bedroom layouts, possible ADA modifications, CMU walls, wood floor and roof trusses, gybcrete, stairs, and the existing site context. My focus on code compliance, practical constructability, and clear permit-ready documentation supports the detailed architectural and structural package this development requires. I can also coordinate the overall documentation with the required mechanical and fire-sprinkler disciplines and support preparation for review by the appropriate Florida-licensed professionals. I am ready to contribute a precise, efficient design package that helps move this affordable multifamily project toward approval and construction. Thanks!

User Avatar
Flag of UNITED STATES

Hello, My licensed Professional Engineer background across architectural, structural, and MEP design directly matches your need for a coordinated multifamily permit package. I prepare construction and permit drawings for residential and commercial projects, including floor plans, elevations, sections, foundations, framing, roof systems, HVAC, plumbing, accessibility coordination, and plan-review revisions. For your two three-story buildings, I can develop the architectural layouts around the repeated 2-bedroom units, coordinate potential first-floor ADA modifications, and document the CMU construction, wood floor and roof trusses, stairs, windows, doors, and building systems. My structural experience covers foundations, load-bearing walls, beams, columns, and framing, while my MEP work includes HVAC layouts, ventilation, plumbing fixtures, water supply, drainage, and equipment schedules. I also provide organized CAD drawing sets and can incorporate the existing DWG files, survey, prior plans, and County comments. I am ready to support a complete, coordinated submission package for the Sarasota project, including structural calculations and engineering documentation within my licensing authority and coordination of required disciplines. Choose me to bring the architectural, structural, and MEP work together accurately and practically. Thanks!

User Avatar
Flag of UNITED STATES

Hello, As a Licensed Professional Engineer experienced with commercial projects, structural systems, CMU and concrete construction, wood and steel framing, MEP coordination, and permit-ready documentation, I can support the complete design package for your two-building, 36-unit multifamily development in Sarasota County. My experience includes developing detailed CAD drawings, engineering calculations, foundations, slabs, masonry walls, wood framing and truss systems, drainage and site plans, HVAC, plumbing, fire-protection coordination, and responses to municipal plan comments. I can work from your existing office-building blueprints, DWG files, survey, county comments, and prototype floor plan to coordinate the architectural, structural, mechanical, accessibility, and permit documentation requirements. I also provide signed and sealed engineering packages where my licensure and the project jurisdiction permit, with close attention to wind loading, applicable building codes, NFPA requirements, and local amendments. I would be pleased to help turn the existing Phase 2 site information into a clear, buildable, submission-ready package for your apartment project. Choose me to provide practical engineering coordination and professional permit documentation from concept through review. Thanks!

User Avatar
Flag of UNITED STATES

Hello, My 10+ years of structural and civil engineering experience across multifamily, commercial, residential, and light-industrial projects directly matches the scale and construction needs of your two-building, 36-unit development. I specialize in permit-oriented engineering documents, foundations, framing, load paths, wind design, and practical solutions for wood, steel, reinforced concrete, and CMU construction. Your Sarasota project requires careful coordination between the repeated unit layout, ADA considerations, three-story framing, wood trusses, gybcrete floor assemblies, 160-mph Wind Exposure D conditions, foundations, and the existing survey and site information. My experience with structural analysis, foundation and footing design, structural framing, roof and floor systems, shear walls, connections, anchorage, grading, drainage, and architectural/structural coordination is well suited to developing a buildable package and addressing plan-review corrections. I can contribute the structural and civil engineering documentation needed for a coordinated permit submission, while coordinating the architectural and MEP components as applicable. I would be glad to discuss this multifamily project and be the engineer you rely on for clear, practical permit documents. Thanks!

User Avatar
Flag of UNITED STATES

Awesome! I’ve handled similar multifamily design and engineering projects, and I can help develop a coordinated submission-ready plan set for your two 18-unit buildings in Sarasota. I’ll focus on efficient 750-square-foot layouts, first-floor ADA compliance, CMU and truss construction, 160-mph wind requirements, HVAC, fire sprinklers, and an exterior that complements the existing stucco-and-mansard office building. I’ve got some thoughts I’d like to run past you so the repeated unit plan stays comfortable, the 20-foot courtyard and stairs work cleanly, and the architectural, structural, mechanical, and sprinkler documents remain coordinated for County review. Best regards, Robert

User Avatar
Flag of POLAND

✅ Hi✅ , Good morning! I am an expert engineer with skills including Civil Engineering, Building Engineering, CAD/CAM, Mechanical Design, Structural Engineering, Construction Management, Architectural Engineering, Building Design, Building Architecture and AutoCAD. Recently, I've done similar project so I am very confident to start your project. I can review your project requirements, understand the technical challenges, and develop a practical and cost-effective solution that meets your specifications. I focus on accuracy, quality, clear communication, and delivering work within the agreed timeline. I would be happy to discuss your project in more detail, understand your expectations, and explain how I can contribute to its successful completion. Please message me here so we can discuss the details. Best regards,

User Avatar
Flag of UNITED STATES

Hi there, Your 36-unit Sarasota multifamily development needs a coordinated, permit-ready package that balances affordability, ADA compliance, hurricane resilience, and efficient 750-square-foot layouts. As an Architectural and Structural Engineering professional with 12+ years of relevant experience, I can develop the architectural, structural, HVAC, and fire-sprinkler documentation around your two three-story CMU buildings, wood-truss systems, 160-mph Exposure D conditions, and existing site constraints. I’ll review the Phase 1 plans, DWGs, survey, County comments, and Option A; optimize repeatable 2-bed/2-bath units; resolve accessible first-floor layouts while preserving space where code allows; coordinate demand water heaters, stacked laundry, 1.5-ton HVAC, stairs, courtyard, and matching stucco/mansard-metal elevations; and organize the set for Florida-licensed discipline review, stamping, and Sarasota County submission. The result will be a practical, coordinated design that reduces clashes, revisions, and permitting delays. Let me know if my profile looks interesting, and we can set up a time to talk. Best regards, Robert W.

User Avatar
Flag of UNITED STATES

Hello, As a Professional Engineer specializing in structural, civil, MEP design, building permits, and construction documentation, I can support the complete engineering package needed for your 36-unit multifamily development. My experience with residential, commercial, and industrial projects is directly relevant to coordinating two three-story CMU buildings, wood floor and roof trusses, foundations, framing, HVAC, plumbing, and permit documentation. I provide structural analysis and design for concrete, timber, steel, and hybrid systems, along with foundation, framing, reinforcement, and detailed construction plans. My MEP services include HVAC layouts and load calculations, plumbing and water supply/drainage design, and coordinated building systems. Using AutoCAD, Revit, Civil 3D, and BIM workflows, I can develop a coordinated construction drawing package from the existing plans, survey, and available CAD information, while addressing code compliance, ADA considerations, site constraints, and Sarasota County review requirements. I can deliver accurate, practical, permit-oriented documentation and coordinate revisions or plan-review responses. I would welcome the opportunity to take responsibility for the engineering and construction-documentation scope of this project. Thanks!

User Avatar
Flag of UNITED STATES

Hello, Our multidisciplinary team provides complete architectural, structural, and MEP design services for multifamily and commercial building projects across multiple U.S. states, making us well suited to coordinate your two-building, 36-unit apartment development into one cohesive permit package. We can prepare floor plans, elevations, sections, construction details, code-conscious documentation, foundation and framing plans, structural calculations, HVAC layouts, equipment schedules, ventilation and mechanical calculations, plumbing layouts, and coordinated construction drawings. The repeated 2-bedroom unit layout, potential first-floor ADA modifications, CMU construction, wood trusses, Florida wind exposure, courtyard arrangement, and existing Phase 1 references can all be addressed within an integrated drawing set. Our services also include professional engineering review and sealing where required, supporting your goal of submission to the Sarasota County building department. I am ready to support this project with a coordinated architectural, structural, and MEP package focused on permit documentation and constructability. Choose me to move your affordable multifamily development toward a professional submission set. Thanks!

内容来自 Freelancer News,版权归原作者所有。

阅读原文 ↗

把喜欢的内容,留在你的新标签页。

打开我的订阅