Mechanical engineer to review 10 mechanism CAD designs this weekend (Nov 14-16)
$100-150 USD / hour
Posted 1 minute ago
•
Ends in 6 days
$100-150 USD / hour
On Policy writes mechanical design problems. Each one is a written engineering brief (loads, interfaces, motion and process rules) plus a reference CAD design (STEP) with its load calculations. An automated checker grades the designs people submit. Before these go out, we want an independent, experienced mechanical engineer to review them. SCOPE 1. Review about 10 reference designs against their briefs. Check strength and stress, that pins, shafts, bearings and gears are sized for the stated loads, fits and clearances through the full range of motion, and whether each part can be made by the stated process. Flag any gaps or ambiguity in each brief. 2. Spot-check about 20 submitted designs that our checker passed or failed, and say whether you agree with its result. Mechanisms: scissor jack, toggle clamp, Geneva indexer, worm reducer, planetary reducer, cycloidal reducer, spur gear reducer, ratchet winch, cam and follower, and over-centre latch. Engine parts may follow later if this goes well. DELIVERABLE A short written verdict for each item: whether it passes (or whether you agree with the checker), the key checks or numbers behind that, and any problems with the brief. Hand calculations are fine. Use FEA where it is the right tool. TIMING (US Central) Start Saturday, Nov 14 and finish by 9 AM CT on Monday, Nov 16. Weekend availability is required. We estimate about 25 to 35 hours of work in total and may split the set between two engineers. PROCESS You sign an NDA before any files are shared. We will likely start with a short paid trial on one design, then release the rest. Hourly, with a not-to-exceed cap agreed up front. YOU HAVE - A mechanical engineering degree and 5+ years of machine design (PE a plus) - Strong hand calculations for pins, shafts, bearings, gears and fasteners, plus FEA experience - A CAD tool that opens STEP files and can check interference through motion (SolidWorks, Creo, NX, Inventor, Fusion or similar) - Clear written English PLEASE ANSWER IN YOUR PROPOSAL 1. A 10 mm steel clevis pin in double shear carries 8 kN. Is it adequate? Give your quick check and say what else you would check. 2. A 6204 deep-groove ball bearing (C about 13.5 kN) carries 2 kN radial and 1 kN axial at 300 rpm. Roughly what L10 life in hours do you expect, and is it fit for 10,000 hours? 3. Which hours (CT) can you work from Sat Nov 14 to Mon Nov 16, and how many hours in total? Which CAD and FEA tools will you use?
Project ID: 40818089
About the project
5 proposals
Open for bidding
Remote project
Active 10 secs ago
Place your bid
Bid amount Email addressBenefits of bidding on Freelancer
Set your budget and timeframe
It's free to sign up and bid on jobs
5 freelancers are bidding on average $105 USD/hour for this job


Hello, Mechanical engineering support backed by 3D CAD, SolidWorks, and Finite Element Analysis makes me well suited to independently review these mechanism designs and their automated-checker results. My team has over a decade of technical delivery experience across engineering, manufacturing, industrial automation, and real-world hardware projects, with a practical focus on reliable, production-ready solutions. For the 10 mm steel clevis pin, the double-shear area is 2 × π(10²)/4 = 157 mm², giving an average shear stress of about 51 MPa at 8 kN. I would also check the steel grade and allowable stress, pin bending, bearing stress in the clevis and joint, edge distances, fatigue, and fit/clearance. For the 6204 bearing, using C = 13.5 kN and the basic radial-equivalent load approximation, the combined 2 kN radial and 1 kN axial load is roughly 2.4-2.6 kN depending on bearing factors. The approximate L10 life is about 150-200 million revolutions, or roughly 8,000-11,000 hours at 300 rpm, so 10,000 hours is borderline and requires the actual equivalent-load factors, lubrication, speed, and reliability target to be confirmed. I can perform the reviews using SolidWorks for STEP inspection, assembly/interference and motion checks, with FEA where it is appropriate, supported by hand calculations for shafts, pins, bearings, gears, and fasteners. I am available for the required weekend window and can commit the requested 25-35 hours, subje Thanks!


Hello, My background is in 3D visualization and engineering, with experience bringing product concepts and detailed designs into clear 3D form. I can review STEP models for visible interference, fit, clearance and manufacturability concerns, and provide concise written verdicts tied to the stated brief. However, the profile does not document the requested 5+ years of machine design, hand-calculation experience for mechanisms, or specific CAD/FEA software, so I would not claim those qualifications without verification. For the clevis pin, the double-shear area is \(2(\pi d^2/4)=157.1\text mm^2\), giving an average shear stress of about 50.9 MPa under 8 kN. Adequacy still depends on the pin material and allowable stress, bearing stress in the lug and clevis, edge distance, bending from clearance, fatigue, and wear. For the 6204 bearing, a combined radial/axial load requires the manufacturer’s equivalent-load factors; using a rough 2 kN equivalent load, \(L_10\approx(13.5/2)^3\) million revolutions, or about 28,000 hours at 300 rpm, so it is broadly above 10,000 hours subject to the actual load factors, lubrication and reliability target. I can contribute engineering review and clear documentation, but CAD/FEA tools and weekend availability are not specified in my profile. Please select me only if those capabilities can be confirmed before the paid trial. Thanks!


Hello, My mechanical engineering background in machine design, 3D CAD, manufacturing, and FEA directly matches this review of mechanisms, calculations, interfaces, and manufacturability. I work with SolidWorks, AutoCAD, and CATIA, and can inspect STEP models, evaluate interference and motion, and provide concise engineering verdicts supported by hand calculations or FEA where appropriate. For the 10 mm steel clevis pin in double shear, the nominal shear stress is approximately 51 MPa (8,000 ÷ 2π·10²/4); I would also check bearing stress in the clevis and pin, bending, edge distance, fatigue, material grade, and fit. For the 6204 bearing, using the combined radial and axial loading with the appropriate equivalent dynamic load and ball-bearing life relation, I would expect roughly 10,000 hours or more at 300 rpm, subject to the actual load factors, lubrication, alignment, and required reliability; I would verify the result rather than relying on radial load alone. I can work over the stated Saturday-to-Monday weekend window, with availability to be agreed within the requested 25-35 total hours. My mechanical design, manufacturing-process planning, SolidWorks, and FEA experience will support clear pass/fail reviews and practical identification of brief gaps. I would be glad to complete the paid trial and review the full set. Thanks!
内容来自 Freelancer News,版权归原作者所有。
阅读原文 ↗