USB Controller Setup for GameSir

£10-20 GBP

Posted 1 minute ago

•

Ends in 6 days

£10-20 GBP

Paid on delivery

Hi, I want to modify a wired game controller (GameSir Tegenaria Lite) by fitting a Raspberry Pi Pico and 2 gyro sensors inside it, based on this open source project with full instructions and wiring diagram: [login to view URL] I'd also like one extra thing included that is not in the official guide: 2 small touch patches on the top edge of the controller, as in this PHOTO: Each patch is a small hole in the shell with a wire passed through and held under conductive tape, and the other end goes to a spare Pico pin. The wiring is the same as the touch point in the guide. I'll handle the firmware myself. I already have the controller and will supply the Pico, the 2 gyro sensors and the conductive tape. Would you already have the small items, such as 100k resistors, thin stranded wire, an M3 screw, electrical tape, hot glue and solder, or should I bring those too? Is this something you'd be able to take on, and what would it cost for labour? Thanks,

Project ID: 40816869

About the project

5 proposals

Open for bidding

Remote project

Active 1 sec ago

Place your bid

Bid amount Email address

Benefits of bidding on Freelancer

Set your budget and timeframe

It's free to sign up and bid on jobs

5 freelancers are bidding on average £20 GBP for this job

User Avatar
Flag of UKRAINE

Hello, Over 15 years in electronic engineering makes me well suited to modify your GameSir controller cleanly and reliably. My experience spans embedded systems, circuit design, Raspberry Pi and ARM-based hardware, giving me the practical background needed to integrate the Raspberry Pi Pico, two gyro sensors and the additional conductive touch points from the alpakka-lite design. I am comfortable working with wiring, soldering, GPIO connections and compact consumer-electronics assemblies. I can also source or provide typical workshop consumables such as 100k resistors, thin stranded wire, an M3 screw, electrical tape, hot glue and solder, subject to the exact parts needed. Since you will handle the firmware, I can focus on the physical installation, correct wiring, insulation and secure placement inside the controller. I would be glad to take on this modification and provide a clear labour cost based on the build scope. Thanks!

User Avatar
Flag of UKRAINE

Hello, Embedded hardware prototyping and Raspberry Pi integration are central to my work, making this controller modification a strong match for my electronics and embedded systems background. I can install the Raspberry Pi Pico and gyro sensors inside the GameSir Tegenaria Lite, follow the Alpakka Lite wiring guidance, and add the two conductive touch patches to spare Pico pins as requested. My experience with circuit design, microcontrollers, Raspberry Pi, sensor integration, soldering-oriented hardware prototyping, and custom electronic builds is directly relevant to fitting everything securely into a compact controller while keeping the wiring reliable. I can also supply common consumables such as 100k resistors, thin stranded wire, an M3 screw, electrical tape, hot glue, and solder, subject to the exact parts needed; you would only need to provide the controller, Pico, gyro sensors, and conductive tape you already have. I would be glad to take on this modification and provide the labour for a careful, tidy installation. Thanks!

User Avatar
Flag of UKRAINE

Hello, Your GameSir modification matches my background in embedded electronics and hands-on hardware prototyping. With 10+ years in electronic hardware development, sensor integration, microcontrollers, troubleshooting, and mechanical/electronic product development, I can implement the Alpakka Lite wiring carefully inside the controller while preserving the shell and controls. I work with Arduino-class systems, Raspberry Pi, embedded systems, analog and digital electronics, and sensors, so adding the two gyro sensors and connecting the two conductive touch patches to spare Pico pins is within my skill set. I can also handle the small mechanical details, creating clean shell openings, routing thin stranded wires, insulating connections, securing components, and using solder and hot glue where appropriate. I can supply typical consumables such as 100k resistors, wire, M3 hardware, electrical tape, solder, and hot glue; you would only need to provide the controller, Pico, gyro sensors, and conductive tape as stated. I would be glad to take on this controller modification and provide the labour for the complete hardware installation. Thanks!

User Avatar
Flag of UKRAINE

Hi there, Would you like the two touch patches routed to specific spare Pico pins, and should they sit symmetrically on the top edge? Do you already know where the Pico and both gyro boards will physically fit inside the shell? The main job is a clean internal layout that keeps the controller comfortable while adding the Pico, two gyro sensors, and the extra touch points without stressing the shell. Based on the open-source guide, I would follow the same wiring logic, then extend it for the two top-edge touch patches and keep the cable paths short and secure. A key risk is noise or a loose mechanical fit inside a small enclosure, especially with moving parts and thin wires. That can be handled by careful strain relief, tidy grounding, insulated routing, and dry fitting before final soldering and glue. Can also check which small parts are already on hand and list anything still needed before starting. If the layout is clear, this should be a straightforward bench build with testing after assembly to confirm every connection is stable. Best, Hlib

User Avatar
Flag of UKRAINE

Hi there, With your GameSir Tegenaria Lite retrofit, I can handle the full hardware integration around the Raspberry Pi Pico: sensor mounting, wiring to match the referenced alpakka-lite guide, clean strain relief, and precise installation of the two added touch patches (shell holes, conductive tape contacts, and spare-PIN wiring) exactly as you described. I have 10+ years of embedded electronics experience with microcontrollers and sensor interfaces, plus solid soldering and EMC-aware wiring practices to keep the controller stable and reliable. You provide the controller, Pico, gyros, and conductive tape, I'll advise on any remaining small components for the 100k resistors, wiring, and fasteners, then deliver a testable, documented hardware build so your firmware can plug in smoothly. Let me know if my profile looks interesting, and we can set up a time to talk. Best regards, Vadym P.

内容来自 Freelancer News,版权归原作者所有。

阅读原文 ↗

把喜欢的内容,留在你的新标签页。

打开我的订阅