PCB design for pen-sized nRF52840 BLE audio recorder + charging case
₹150000-250000 INR
Posted 1 minute ago
•
Ends in 6 days
₹150000-250000 INR
Paid on delivery
PCB designer needed for a pen-sized nRF52840 Bluetooth audio recorder and its charging case (rigid-flex), pilot run of 5-10 units, Bengaluru, India. THE PRODUCT A working ballpoint pen (12.5 mm diameter, ~153 mm long) that records conversations to onboard flash and syncs to a phone app over Bluetooth Low Energy. It also logs motion-sensor data. It snaps magnetically into a charging case with its own battery. Proof of concept already works on a Seeed XIAO nRF52840 Sense. Detailed drawings and firmware shared after an NDA. BOARDS (pen boards must fit a ~10.9 mm inner diameter) 1. Pen main board ~8 x 30 mm, both sides populated, under a translucent antenna window 2. Flex cable ~90 mm down the barrel past the battery 3. Sensor disc ~9 mm round behind the refill (IMU + nib force sensor) 4. Case board ~8 x 10 mm (USB-C in, case LiPo charging, pen charging via pogo pins) Pen battery 10350/10440 Li-ion; case battery ~5 x 17 x 80 mm LiPo (~700 mAh). STARTING PARTS (suggestions welcome): nRF52840 module or bare chip + chip antenna; 1-2 PDM MEMS mics; 64-128 MB SPI flash; 6-axis IMU (LSM6DSO/BMI270); Li-ion charger + fuel gauge + protection with very low sleep current; centre + ring charging pads with magnet; LED ring; one button. Case: charger IC, charge path to pen pins, gauge, Hall sensor, status LED. Targets: full day of recording, weeks of standby, 5 m+ BLE range from a mostly aluminium pen. DELIVERABLES 1. Architecture review of part choices (week 1) 2. Schematics for all four boards 3. Layouts, stack-up and flex design, Gerbers, BOM, pick-and-place for JLCPCB assembly 4. 3D STEP models of each board 5. Bring-up support for prototype round 1 and one revision for round 2 6. Native source files (KiCad preferred, Altium OK) Timeline: schematics ~3 weeks, layouts ~week 6, round 2 ~week 12. TERMS: NDA; all design files and IP assigned to us; milestone payments; a small paid first task (review our parts list and block diagram) before the main contract. TO APPLY: share 2-3 small battery-powered boards you designed that reached a real product (photos; nRF52 or rigid-flex a strong plus), a quote broken down by the milestones above with earliest start date, your design tool, and your location / whether you can meet in Bengaluru.
Project ID: 40813130
About the project
1 proposal
Open for bidding
Remote project
Active 22 secs ago
Place your bid
Bid amount Email addressBenefits of bidding on Freelancer
Set your budget and timeframe
It's free to sign up and bid on jobs
1 freelancer is bidding on average ₹165,000 INR for this job


The tight parts here are the 10.9 mm barrel, the antenna on a mostly aluminium pen, and a sleep current low enough for weeks of standby. I'd settle the antenna keepout, flex bend radius and charger/gauge choice in the week 1 review, before any schematic work. I'm fine with the NDA, IP assignment and a paid first task. I design in KiCad and can start right away. Some of my small battery-powered boards, with protection, charging and low-power wireless, are in my portfolio. I'll send the milestone breakdown after the parts review. I work remotely and can handle bring-up support from here. Do you want the flex and pen board as one rigid-flex part or separate boards?
内容来自 Freelancer News,版权归原作者所有。
阅读原文 ↗