3-Piece Ranga Turtle Gravity Die Design

₹750-1250 INR / hour

Posted 1 minute ago

•

Ends in 6 days

₹750-1250 INR / hour

3-Piece Gravity Die Design for a Solid Ranga Turtle Figurine, Exact 2500 g Weight (SolidWorks) About Ranga Ranga (रांगा) is the traditional Indian casting metal used for this project. It is tin-based, but locally sourced Ranga may contain other metals, so its exact composition and density must be confirmed before design (see Step 1). Throughout this brief, “Ranga” means our actual casting metal. Project overview I need a hand-operated, 3-piece permanent die designed for gravity casting a solid turtle figurine in Ranga. Each finished Ranga casting must weigh 2500 g. The 3D model is ready as a Parasolid (.x_t) file. The die will be made by a toolroom in Indore, India, and used by a traditional caster who normally pours Ranga into sand moulds, so it must be simple to operate by hand. Casting details Metal: Ranga, sourced locally (composition to be confirmed) Casting: solid, single piece Target weight: 2500 g of finished Ranga, with a tolerance of ±15–25 g Current model size: [length × width × height in mm]; current model volume: [cm³ from SolidWorks] Quantity: a few hundred Ranga castings over several years Finish: mirror-smooth as cast, with no polishing afterwards Step 1: Ranga density check before design (required) Please: Guide us through a simple water-displacement test on a sample of our actual Ranga. We will send you the weights and readings. Review our results and confirm the density of our Ranga, or advise if a lab or XRF test is needed. Calculate the exact finished volume needed for 2500 g of Ranga, and the scale factor for the model. Die requirements Material: 1.2083 ESR stainless mould steel, hardened to about 48–52 HRC Three-piece split, with parting lines planned to release the legs cleanly Model scaled so that the finished Ranga casting, not the cavity, equals 2500 g Shrinkage allowance for Ranga applied once only, and clearly stated Gate and feeder on the underside (belly), sized to keep the Ranga casting fully solid with no internal voids A small hidden recess under the belly for fine weight adjustment, if needed to hold the tolerance Air vents for a clean, pinhole-free Ranga surface Locating pins, a clamping arrangement and handles for manual use Suitable for standard CNC machining and EDM Deliverables Ranga density confirmation, volume calculation and scale factor, in writing 3D die assembly in native SolidWorks format and STEP 2D manufacturing drawings with tolerances A simple operating guide for the caster: die preheating, coating, pouring Ranga, opening and storage Support for a prototype check before steel is cut: a 3D-printable turtle model at final size for a trial casting in our Ranga, with design corrections if the weight is off One round of revisions after the toolroom’s review Required experience Proven work on gravity or permanent moulds for low-melting metals (tin, pewter, zinc) or aluminium Experience designing castings to a target weight Strong SolidWorks skills Please share 2–3 relevant past projects

Project ID: 40812566

About the project

1 proposal

Open for bidding

Remote project

Active 40 secs ago

Place your bid

Bid amount Email address

Benefits of bidding on Freelancer

Set your budget and timeframe

It's free to sign up and bid on jobs

1 freelancer is bidding on average ₹1,100 INR/hour for this job

User Avatar
Flag of INDIA

You need a 3-piece gravity die design for a solid Ranga turtle figurine. Trygve Studio's expertise is architecture, interiors and product development, with a team of architects, engineers and 3D visualizers. We will approach this by calculating the required volume based on your material density and then designing the die assembly and manufacturing drawings in SolidWorks. Please view our profile and message us to discuss the details.

内容来自 Freelancer News,版权归原作者所有。

阅读原文 ↗

把喜欢的内容,留在你的新标签页。

打开我的订阅