Voice-Activated Auto-Dialer Integration

$250-750 USD

Posted about 1 hour ago

•

Ends in 6 days

$250-750 USD

Paid on delivery

I need a small, self-contained kit that listens for a spoken trigger phrase, seizes my existing internet-based phone line, automatically dials a list of mobile and land-line numbers, plays a pre-recorded announcement, then transfers the caller straight to a live operator or secondary number. After the transfer the announcement must stop and full duplex conversation must be possible. The hardware and software should work reliably on standard VoIP/SIP services and be simple for me to re-record the message or update the dial list. A solid-state relay output is also required so that, once the outbound call is answered, I can switch an external device. Typical tools that make sense here include Asterisk/FreePBX, Raspberry Pi, ESP32 voice modules, Twilio, or similar SIP gateways—but I am open to your preferred stack as long as it delivers hands-free voice activation, flawless call bridging, and easy configuration. Please give me: • A complete parts list or ready-made board recommendation • All code, dial-plan, and configuration files • Clear setup instructions that a technically minded user can follow without specialist test gear I will test by issuing the voice command in a normal office environment; the system must dial, play the message audibly, switch the relay, and connect me to my chosen live number without manual intervention.

Project ID: 40812433

About the project

61 proposals

Open for bidding

Remote project

Active 23 mins ago

Place your bid

Bid amount Email address

Benefits of bidding on Freelancer

Set your budget and timeframe

It's free to sign up and bid on jobs

61 freelancers are bidding on average $596 USD for this job

User Avatar
Flag of UKRAINE

Hello, My embedded-systems and Raspberry Pi experience is well suited to building a compact voice-activated VoIP controller with reliable hardware interfacing. I can develop the Raspberry Pi-based logic for the spoken trigger, automatic dialing, announcement playback, call transfer, and solid-state relay activation, while keeping the system self-contained and practical for office use. I can also support the electronics side through component selection, circuit design, embedded firmware, and hardware documentation. The deliverables can include a complete parts list or board recommendation, source code, configuration files, dial-plan integration, relay interface details, and clear setup instructions so the announcement and dial list can be updated without specialist test equipment. My background in embedded systems, Raspberry Pi, ESP32, networking protocols, and hardware prototyping allows me to address both the VoIP software and physical control requirements. I would be glad to build this integration as a dependable, easy-to-configure kit. Thanks!

User Avatar
Flag of KENYA

Your post has three hard parts that must work together: a trigger you can speak without touching anything, a clean seizure of your existing SIP line, and a bridge that stops the announcement the moment the live operator answers. I would build the core on Asterisk on a Raspberry Pi 4 with a USB microphone and speaker, registering your SIP trunk through PJSIP for standard providers. The trigger runs offline on the Pi with openWakeWord or Vosk. A Python service listens, then uses Asterisk's ARI to originate each number from a plain text list you edit. On answer, Playback plays your recorded message from a WAV file you replace by copying a new file over the old one. When the transfer fires, playback stops and the called party is bridged straight to your live number, leaving full duplex audio between them. The relay is a GPIO pin driving an optically isolated solid-state relay, switched by the same ARI event that fires on answer. I would test the full sequence in your office with your exact trigger phrase and send the configs, parts list and setup notes. Please tell me your SIP provider, whether you already run FreePBX, and which Pi you can source. I can start as soon as you send those details.

User Avatar
Flag of PAKISTAN

Hi, I am an embedded systems engineer with over 16 years of experience. I have extensive experience with embedded control, voice interfaces and SIP integration, and can handle both the hardware and software for your kit. I would use a compact Raspberry Pi running Asterisk, with local voice activation and straightforward controls for updating the dial list and re-recording your announcement. Once an outbound call is answered, the system would switch the solid-state relay, play your message, then connect the recipient to your chosen live number. Playback would stop before the conversation begins, with full duplex audio between both parties. I will provide a complete parts list or suitable board recommendation, all source code and dial-plan/configuration files, and clear setup instructions. I will also include a practical test procedure covering office voice activation, dialing, audible playback, relay switching and call bridging without specialist test equipment. Could you confirm your SIP provider, whether numbers should be dialed sequentially or simultaneously, and the voltage/current the relay needs to switch? My bid covers development and documentation; hardware and service charges would be separate. Please contact me to discuss details.

User Avatar
Flag of UKRAINE

My 10+ years in embedded systems and industrial electronics make me well suited to build a dependable, self-contained voice-activated dialer with relay control. I can develop the solution around Raspberry Pi and integrate the SIP/VoIP call flow, spoken trigger, announcement playback, call bridging, and solid-state relay output into one practical kit. My experience includes ESP32, microcontrollers, sensors, relays, embedded control systems, automation, troubleshooting, commissioning, and complete product development from component selection through testing and documentation. That directly supports your need for reliable hands-free operation, easy message and dial-list updates, and hardware that can switch an external device when the outbound call is answered. I will provide the parts or board recommendation, code, dial plan and configuration files, wiring information, and clear setup instructions suitable for testing in a normal office environment. I am ready to deliver a robust Raspberry Pi-based integration tailored to your SIP service and choose me to take this project from design through working prototype.

User Avatar
Flag of INDIA

Hello, I am Dr. Rajesh Rolen, PhD in Computer Science & Engineering, with experience of over 20+ years in Twilio, Raspberry Pi As a preferred freelancer in the top 1%, I have done 400+ projects here on freelancer.com, I have 4.9 ratings out of 5 on average, which showcases my quality of work and timely delivery. Key Highlights: - Free Hosting Support on the Cloud or any desired platform. - Free 3 months of post-delivery support to ensure that our client doesn’t face any challenges after the launch of the project. - Free Dedicated tester on projects to ensure quality delivery, so clients don’t need to act as a tester. - 10+ Years experience UI/UX team to ensure intuitive UI. Portfolio: https://www.freelancer.com/u/Microlent Please open the chat and send me a message, so we can have a more detailed discussion about the project to give you the project timeline and cost. Thank you for considering my services. I look forward to engaging in a productive conversation and understanding how I can be of assistance in bringing your project to life. Regards Rajesh Rolen

User Avatar
Flag of COLOMBIA

My 8+ years in embedded systems engineering and Raspberry Pi development make me well suited to build this self-contained voice-activated dialer and relay controller. I can design the hardware and firmware integration around your existing VoIP/SIP service, with reliable trigger handling, outbound call sequencing, announcement playback, call bridging, and a solid-state relay output for the external device. My background includes RF and embedded controller design, circuit development, firmware in C/C++, system integration, validation, troubleshooting, and complete technical documentation. That experience is directly relevant to producing a practical parts list or board recommendation, robust wiring and interface design, configuration files, and clear setup instructions that do not depend on specialist test equipment. I can deliver a maintainable kit with simple message and dial-list updates, full-duplex transfer behaviour, and documented integration between the Raspberry Pi, telephony stack, and relay hardware. Choose me to develop and document the complete solution from concept through tested implementation.

User Avatar
Flag of PAKISTAN

Hello, Combining Asterisk PBX with Raspberry Pi and embedded-systems expertise makes me well suited to build this self-contained voice-activated dialer. I can create the SIP call flow for trigger activation, automatic dialing, announcement playback, live call transfer, full-duplex conversation, and relay control after the outbound call is answered. My experience with Linux, Raspberry Pi, and embedded systems supports a practical kit that is maintainable outside specialist laboratory equipment. I can provide the complete parts list or board recommendation, source code, Asterisk dial plan, SIP configuration, relay interface details, and clear setup instructions. The dial list and recorded announcement can be kept easy to update, while the system remains suitable for standard VoIP/SIP services. I would be glad to deliver a reliable, hands-free integration that connects the hardware and telephony functions into one straightforward system. Thanks!

User Avatar
Flag of UNITED ARAB EMIRATES

Hi, I'm Waqas. I can help you create a voice-activated auto-dialer that meets your specifications for seamless call integration and reliable performance. I’d start by selecting the right components, including a Raspberry Pi and compatible voice module, ensuring they work with your VoIP/SIP services. I’ll develop the necessary Asterisk dial plan and code to handle the voice recognition, dialing, and announcement playback. Before handover, I’ll provide clear setup instructions and test the system to ensure it performs as expected in your office environment. What specific features or customization options do you have in mind for the pre-recorded announcement? Best regards, Waqas

User Avatar
Flag of VIETNAM

Hello. "HANDS-FREE SIP DIALING AND RELIABLE LIVE CALL TRANSFER" - You need a self-contained unit that listens for a voice command, places calls, plays an announcement, activates a relay, and then hands the call over with clear two-way audio. I would design this around a Raspberry Pi with Asterisk or a suitable SIP service, plus a voice-trigger module and isolated solid-state relay. The dial plan would manage the call sequence, announcement playback, answer detection, relay activation, and transfer to the selected operator number. I would also make the message and dial list easy to update without changing the core code. Before choosing hardware, I would verify compatibility with your SIP provider and test call bridging, audio in both directions, relay timing, and failure handling. Deliverables would include the parts list, source code, configuration files, and clear setup instructions. The outbound workflow should use numbers with documented consent and comply with applicable calling rules. Which SIP provider and hardware are you currently using, and should the trigger phrase start one fixed call sequence or let you select a dial list? Looking forward to working with you.

User Avatar
Flag of SERBIA

I can build a reliable, self-contained voice-activated auto-dialer around a practical SIP/Asterisk or hosted VoIP architecture, with hardware chosen for dependable office operation. The solution will include: • Spoken trigger detection with hands-free activation • Configurable mobile and land-line dialing lists • Pre-recorded announcement playback • Seamless transfer to a live operator or secondary number, with announcement termination and full-duplex audio • Solid-state relay control when the outbound call is answered • Simple message and dial-list updates • Complete source code, dial plan, configuration files, parts recommendations, and step-by-step setup documentation I’ll design the call flow carefully for SIP reliability, handle answer detection and transfer states, and make the system straightforward to test without specialist equipment. I can also structure the configuration so future changes do not require rebuilding the application. The final setup will be validated against your normal office voice-command workflow, including dialing, announcement playback, relay switching, and live call connection.

User Avatar
Flag of UNITED STATES

Hi, one thing worth settling before any code: on mobile numbers a SIP "answered" signal also fires when voicemail picks up, so a relay keyed off a raw answer will switch your device for a voicemail greeting. I'd have the called party press 1 after the announcement to confirm a real person, and only then fire the relay and bridge the call. What I'd build: a Raspberry Pi 5 running Asterisk, registered to your existing SIP line as a trunk, a USB conference speakerphone for mic and speaker (its echo cancelling is what makes full duplex usable in an office), and a small Python service doing offline wake-word detection with Porcupine or Vosk, so nothing depends on cloud speech. It originates calls through AMI; the dialplan plays your recording, waits for the confirm digit, drives a GPIO pin into a DC-input SSR, then stops playback and joins the call to you or your secondary number. The handoff note covers the parts list, setup from a blank SD card, swapping the message (drop in a WAV) and editing the dial list (a plain text file). Which SIP provider are you on, and should the list ring all at once or in sequence? Also, what load does the relay switch? Thanks, Daniel

User Avatar
Flag of UNITED STATES

Hi, Adelman here from Texas VOICE-ACTIVATED SIP AUTO-DIALER AND CALL BRIDGING: you need a hands-free system that detects a spoken command, makes outbound calls, plays your announcement, activates a relay, and transfers the call without interrupting conversation. I'd use a Raspberry Pi with Asterisk for call control, SIP integration, and full-duplex audio bridging. A separate voice trigger module would handle activation, while a solid-state relay would switch the external device after call answer. I'd also make the dial list and recorded message easy to update. Can your existing VoIP provider support SIP registration and outbound call transfers? Looking forward to work with you.

User Avatar
Flag of PHILIPPINES

Hi there, The hard part is ensuring reliable call handling and voice recognition in a typical office environment. First, we need to focus on building a robust system that can accurately recognize your trigger phrase and manage the call flow without glitches. Using a Raspberry Pi combined with Asterisk will allow us to leverage existing SIP services while providing flexibility for updates. I can provide a detailed parts list, configuration files, and code necessary for setup, ensuring everything is straightforward for a technically minded user. What specific external device do you intend to control with the relay output? Thank you.

User Avatar
Flag of INDIA

Hi, I can build your voice-activated auto-dialer kit using a Raspberry Pi integrated with Asterisk PBX and a SIP gateway. I will implement a local wake-word listener that triggers a custom dial-plan to handle the sequential calling, audio playback, and the seamless bridge to your live operator, ensuring a full-duplex conversation once connected. I have extensive experience building complex automation and communication systems, including VoIP and Twilio integrations for enterprise-grade platforms. I'll utilize GPIO-controlled solid-state relays on the Raspberry Pi to provide the physical hardware trigger you need upon call answer. • Complete BOM (Raspberry Pi, Relay Module, Audio Interface, and SIP Hardware) • Custom Asterisk dial-plan and configuration for automated sequencing • Python-based trigger script for voice activation and relay control • Step-by-step setup guide for recording messages and updating the dial list Do you have a preferred SIP provider already, or would you like a recommendation for one that works best with this hardware? Let's connect in chat so we can get started right away! Best regards, Mohammad Juned

User Avatar
Flag of INDONESIA

Hi Bill, I hope you are having a wonderful day. I have carefully reviewed your requirements and I am confident I can deliver this solution. I will build a hands-free auto-dialer using Raspberry Pi and Asterisk with SIP integration, voice trigger detection, automated dialing, message playback, call bridging and solid-state relay control. I will also provide editable settings and clear setup instructions. Do you already have a preferred SIP provider and relay hardware? I have experience with Python, Linux, VoIP, SIP, APIs and real-time voice AI integrations. I can deliver reliable results and start immediately once the plan is finalized. Please feel free to discuss the details with me via chat. Thank you!

User Avatar
Flag of JORDAN

Hello, I am an Electrical/Electronics Engineer with 15+ years of hands-on experience in embedded systems, electronic hardware design, and industrial control. I can develop this voice-activated calling system using Raspberry Pi and Asterisk, integrating a microphone, SIP connectivity, and an isolated solid-state relay output. The system will detect the trigger phrase, automatically dial your configured numbers, play the recorded announcement, detect call answering, activate the relay, and transfer the call to a live operator with full-duplex audio. I will provide the hardware parts list, wiring diagrams, complete source code, SIP configuration, dial plan, and setup instructions. The phone list and recorded message will be easy to update. Best regards, Hamza

User Avatar
Flag of INDONESIA

You want one spoken phrase to dial your list, play the announcement, switch the relay and put you through to a live number, with nothing to touch. I can build this for you, with the parts list, dial-plan and config files, and setup notes a technical person can follow without special gear. I'll stay on it until it works in your office the way you'll test it, and I'll cover bug fixes and support after handover. Which SIP provider is your existing internet phone line with? Happy to get started whenever suits you. Sela

User Avatar
Flag of PAKISTAN

Hi, I understand you need a hands-free auto-dialer that hears a trigger phrase, uses your existing SIP line, calls your list, plays an announcement, activates a relay, and bridges the answered call to a live operator with full duplex audio. I can build this around Linux and Asterisk PBX, with a suitable embedded voice module and relay interface. I will provide the parts list, complete dial plan and configuration files, simple message and dial-list updates, setup steps, and testing guidance for a normal office environment. The call flow will stop the announcement as soon as the transfer is answered and keep the conversation clear. Which SIP provider and hardware do you already have, and how many numbers should the system dial per activation? Please start the chat and let’s discuss your SIP provider and preferred hardware.

User Avatar
Flag of MOROCCO

Hi, I will deliver a Raspberry Pi kit that hears your trigger phrase, dials SIP numbers, plays the announcement, switches a relay and bridges to a live operator. I’ll provide parts list, code, dial‑plan and guide within 7 days for $600. Start now with demo script?

User Avatar
Flag of UKRAINE

Hi there, Which SIP provider and phone line format should the kit control, and do you want the relay to switch on answer or on answer plus audio detection? What is the exact trigger phrase, and should it ignore false activations from normal office noise? The core challenge is making voice activation, outbound dialing, playback, and live transfer behave like one clean call flow. A practical stack is Raspberry Pi with Asterisk, SIP trunk support, and a small relay board, with recordings and dial targets stored in simple config files or a CSV. The risky part is timing: the announcement must stop exactly when the call is bridged, while the relay switches at the right moment. That can be handled with Asterisk call progress events and a hangup-safe dialplan, plus a short test loop for voicemail, busy, and no-answer cases. Can provide a complete parts list, the dialplan, AGI or shell scripts, relay control logic, and setup steps that do not need special lab gear. The handoff can be made easy to edit later, so changing the message or number list is a file update, not a rebuild. Best, Hlib

内容来自 Freelancer News,版权归原作者所有。

阅读原文 ↗

把喜欢的内容,留在你的新标签页。

打开我的订阅