KiCad PCB revision + ESP32 firmware update for wireless battery monitor (2 boards)
₹1500-12500 INR
Posted 1 minute ago
•
Ends in 6 days
₹1500-12500 INR
Paid on delivery
We have a working 2-board wireless battery monitoring system and need an experienced hardware engineer to complete a design revision (rev-B) and production files. EXISTING SYSTEM (all files provided, KiCad + Arduino/ESP-IDF source): - Transmitter PCB: ESP32, 2x ADS1115 (16-bit ADC) reading 4S/5S/6S lithium cell voltages via divider network, 3 relay outputs, XL1509 buck + LM1117 3.3V LDO. Powered directly from the battery pack (max 16.8V). - Receiver PCB: ESP32 + 3.5" ILI9481/ILI9488 TFT, receives data via ESP-NOW. - Firmware for both boards is working (cell readings, two-point calibration, ESP-NOW, display UI). SCOPE OF WORK: 1. Review the existing KiCad project and firmware. 2. Transmitter rev-B design changes: - Add proper input protection: TVS, input fuse / overcurrent protection, inrush/filtering ahead of the buck converter (battery is hot-plugged in the field) - Add TMP102 temperature sensor on the existing I2C bus (address must not clash with ADS1115s at 0x48/0x49) - Keep JST battery connector; move USB connector 5mm outward 3. Generate production files: Gerbers, BOM (LCSC/JLC-available parts), pick-and-place with correct rotations, schematic PDF. 4. Firmware update: TMP102 reading, fan relay ON above 40C with hysteresis, temperature shown on receiver display. 5. Test firmware on rev-B sample boards (boards will be shipped to you) and provide a test video. REQUIREMENTS: - Strong KiCad experience with power input protection design - ESP32 + I2C firmware experience - Must be able to do SMD soldering/rework yourself, and own a current-limited bench power supply and multimeter IN YOUR PROPOSAL, PLEASE ANSWER: 1. For a 16.8V max battery input feeding a buck converter rated 40V input, which TVS would you choose and why? 2. Share a KiCad board you designed with input protection. 3. Your timeline for steps 1-4. Milestone-based payment. Proposals without answers to the questions will not be considered.
Project ID: 40812317
About the project
2 proposals
Open for bidding
Remote project
Active 21 secs ago
Place your bid
Bid amount Email addressBenefits of bidding on Freelancer
Set your budget and timeframe
It's free to sign up and bid on jobs
2 freelancers are bidding on average ₹4,250 INR for this job


I'd pick an SMBJ18A. Its 18V standoff sits above your 16.8V max, so it won't leak or run hot on a full pack, and its clamp of about 29V stays well under the buck's 40V rating. I'd put it after the fuse and a series filter, so hot-plug spikes are clipped before the XL1509. Most of my work is under NDA, so I can't share a protected-input KiCad board. My portfolio has a 5-cell Li-ion protection and monitoring board with Wi-Fi. Timeline: review 1 day, rev-B schematic and layout 3 days, production files 1 day, firmware 2 days, then testing and video once the samples arrive.


I can start right now I have checked the details. For the 16.8V max battery input hot-plugged in the field, I would select a bidirectional TVS diode with a working standoff voltage ($V_{RWM}$) around 20V to 22V (such as an SMBJ20A or SMAJ20A series), ensuring a clamping voltage well below the absolute max rating of the XL1509 buck converter while safely
内容来自 Freelancer News,版权归原作者所有。
阅读原文 ↗