Loading Ramp Structural Design Review
$8-15 USD / hour
Posted 1 minute ago
•
Ends in 6 days
$8-15 USD / hour
Structural Engineer – Loading Ramp Design Review & Calculations (Australian Standards) We are seeking an experienced structural engineer to independently review, verify, and revise preliminary calculations for a mining-site loading ramp retaining structure in Western Australia. The structure consists of an inverted 40 ft high-cube shipping container, partially buried and filled with compacted ROM rock, forming the retaining edge of a ramp used by a Cat 950 GC wheel loader. The preliminary design includes two rows of M20 Grade 8.8 tie rods, RHS 100×50×4.0 C350 walers, and the retained container floor frame acting as the upper restraint. The loader operates over the central 20 ft, with angled berms covering both end sections. Design drawings, specifications, and Excel calculation workbooks are provided. Scope of Work 1. High-Cube Container Assessment - Verify the revised geometry (approximately 2.7 m wall height, 1.8 m exposed, and 0.9 m buried). - Evaluate two versus three tie rows or trimming the walls to approximately 2.1 m. - Assess wall bending, tie positions, load distribution, and below-ground restraint. - Recommend the most structurally adequate and practical configuration. 2. Tie, Waler & Connection Verification - Independently verify M20 tie-rod loads, RHS waler capacities, and corrugated wall strength. - Assess 6 mm versus 10 mm galvanised plate washers and crush-tube load transfer. - Check local bearing, deformation, connection details, corrosion allowance, and design life. - Review the existing floor-frame restraint, welds, unstiffened cut edge, and relevant end-wall details. 3. Structural Stability & Loading - Review loader wheel/axle loading and the assumed 30 kPa surcharge. - Verify lateral earth pressures, sliding, overturning, and foundation bearing. - Assess ROM fill and foundation assumptions, drainage, and construction-stage stability. - Identify any missing site information or testing requirements. 4. Calculations & BOM - Review and correct the existing calculations using applicable Australian standards. - Provide updated, transparent and editable Excel calculations. - Update the Bill of Materials (BOM), including member sizes, connection specifications, and quantities. - Clearly identify unresolved assumptions and conditions requiring verification before certification. Required Deliverables - Technical design review report (PDF) with findings and recommendations. - Revised, fully editable Excel calculation workbook. - Recommended high-cube configuration and verified connection details. - Updated technical BOM (Excel). - Summary of outstanding engineering issues and required site confirmations. Attached Reference Documents 1. Tie & Waler Design – Draft 3 (Word): Design assumptions, sketches, specifications, installation sequence, and outstanding checks. 2. Tie & Waler Calculations – Draft 3 (Excel): Original loader, stability, wall, tie/waler calculations, and BOM. 3. Tie & Waler Calculations – Draft 5 (Excel): Latest calculations, updated washer/connection checks, and revised BOM. Primary calculation reference. 4. Engineer Scope of Work – Draft 1 (Word): Overall engineering review and project requirements, provided for reference only. All supplied calculations are preliminary and must be independently verified. Requirements - Experience with steel structures, retaining walls, structural connections, and engineering calculations. - Familiarity with AS 4678, AS 4100, AS/NZS 4600, and AS/NZS 1170. - Ability to independently assess existing calculations and justify design recommendations. - Mining or heavy-equipment infrastructure experience preferred. This assignment covers technical design verification and calculation updates only. Formal engineering certification, construction drawings issued for construction, site inspections, construction-stage approvals, and final sign-off are excluded. Timeline & Application Urgent, remote, fixed-price assignment. The high-cube configuration and washer/crush-tube assessment are the immediate priorities because they affect material procurement. Please provide relevant experience, your proposed approach, estimated turnaround time, and fixed-price quotation. Work may be divided into an initial priority-review milestone and a final calculation/BOM milestone.
Project ID: 40811316
About the project
4 proposals
Open for bidding
Remote project
Active 10 secs ago
Place your bid
Bid amount Email addressBenefits of bidding on Freelancer
Set your budget and timeframe
It's free to sign up and bid on jobs
4 freelancers are bidding on average $16 USD/hour for this job


My structural engineering and steel detailing experience is directly suited to reviewing this loading-ramp system, including industrial frames, steel structures, platforms, connection details and fabrication-ready documentation. I can independently examine the preliminary container, tie-rod, RHS waler and restraint design and translate the findings into clear engineering deliverables. I work with structural and civil engineering requirements and can review the supplied Excel calculations, drawings and assumptions covering wall behaviour, tie and waler capacity, connection load transfer, stability, bearing and construction details. My AutoCAD capability supports accurate review and revision of the geometry, connection details and updated BOM, while my structural detailing background helps identify practical issues such as local bearing, welds, cut edges, stiffening and fabrication constraints. I will clearly separate verified items, revised calculations, unresolved assumptions and site information still required under the applicable Australian standards. I am ready to provide a professional technical review report, editable calculation workbook, revised configuration recommendations and updated BOM for this urgent assignment. Choose me for a focused structural review that connects engineering checks with practical steel detailing.


✅ Hey Mate✅ , Good morning! I am an expert engineer with skills including Bill of Materials (BOM) Analysis, AutoCAD, Civil Engineering, Geotechnical Engineering, Construction Management, Construction Engineering, Structural Engineering and Building Architecture. Recently, I've done similar project so I am very confident to start your project. I can review your project requirements, understand the technical challenges, and develop a practical and cost-effective solution that meets your specifications. I focus on accuracy, quality, clear communication, and delivering work within the agreed timeline. I would be happy to discuss your project in more detail, understand your expectations, and explain how I can contribute to its successful completion. Please message me here so we can discuss the details. Best regards,
内容来自 Freelancer News,版权归原作者所有。
阅读原文 ↗