PCB design: compact wearable (ESP32-S3 + nRF9160 LTE-M/GNSS + PPG sensor), 4-layer, JLCPCB assembly
$250-750 CAD
Posted 1 minute ago
•
Ends in 6 days
$250-750 CAD
Paid on delivery
PCB design: compact wearable (ESP32-S3 + nRF9160 LTE-M/GNSS + PPG sensor), 4-layer, JLCPCB assembly I am developing a wrist-worn safety bracelet for elderly people (fall detection, SOS button, two-way voice calls, GPS, heart rate / SpO2 / skin temperature display). A working breadboard prototype and its firmware already exist. I need an experienced designer for the schematic and PCB layout of the first prototype board (V1), ready for JLCPCB assembly (5 boards). Main parts (already selected, LCSC numbers provided): - ESP32-S3-MINI-1-N4R2 (Wi-Fi) - Nordic nRF9160 (LTE-M + GNSS) with LTE chip antenna (incl. 700 MHz) and GNSS antenna - MAXM86161 optical sensor (bottom side, against the skin) - BMI270, TMP117, MAX17048, BQ21040, TPS63802, MAX98357A, ICS-43434 - Li-Po battery, magnetic charging pads (no USB connector), vibration motor, 2 buttons Key requirements: - Very compact: enclosure max 45 x 40 x 15 mm (PCB about 38 x 34 mm), two-sided assembly - Good LTE antenna performance on a small board (top priority) - Written power budget before layout (peak currents of radios + audio amplifier) - ESD protection, sealed/waterproof device (no voltage on charge pads when off the dock) - The product will later go through medical-device certification, so good practice from V1 Deliverables: schematic, editable source files (KiCad or EasyEDA - client owns them), Gerbers + BOM + CPL for JLCPCB, STEP 3D model of the assembled board, power budget, antenna tuning notes. The full specification (PDF) is attached. In your proposal, please include: 1. Examples of boards you designed with cellular modules (nRF91 or similar) and small antennas 2. Wearable or small battery-powered experience 3. KiCad or EasyEDA 4. Fixed price and timeline 5. Whether you include a design review call and support after the boards arrive Proposals without cellular/antenna experience will not be considered.
Project ID: 40810428
About the project
10 proposals
Open for bidding
Remote project
Active 8 secs ago
Place your bid
Bid amount Email addressBenefits of bidding on Freelancer
Set your budget and timeframe
It's free to sign up and bid on jobs
10 freelancers are bidding on average $520 CAD for this job


Hi, I understand you need a compact 4-layer V1 board for the ESP32-S3, nRF9160 LTE-M/GNSS, PPG sensing, audio, charging, and battery power within a 38 x 34 mm area. I will first prepare the power budget, then complete the schematic and careful RF/PCB Layout with antenna clearance, grounding, ESD protection, thermal checks, and two-sided Assembly planning for JLCPCB. I have worked with cellular modules and small-board antennas, including wearable and battery-powered designs. I can work in KiCad or EasyEDA and will provide editable files, Gerbers, BOM, CPL, STEP model, and antenna tuning notes. Fixed price: CAD 650. Timeline: 18 days, including one design review call and support after the first boards arrive. For the nRF9160, which exact LTE and GNSS antenna parts, enclosure materials, and carrier bands must the first prototype support? Please start the chat and let’s discuss the PDF, enclosure limits, and antenna priorities.


Hello, Wearable devices, RF connectivity, and compact battery-powered electronics are central to my PCB and embedded-systems work, making this V1 safety bracelet closely aligned with my expertise. I design 1-8 layer boards using KiCad, EasyEDA, and Altium Designer, with experience integrating ESP32 and Nordic wireless platforms, sensors, power systems, and manufacturing-ready documentation. I can deliver the editable schematic and PCB layout, Gerbers, BOM, CPL, STEP model, component footprints, and supporting engineering reports. My background in RF and wireless communication, low-power IoT, wearable devices, medical monitoring systems, and sensor integration is relevant to the nRF9160/antenna constraints, two-sided 4-layer layout, PPG placement, power budgeting, and JLCPCB assembly requirements. I will also include antenna tuning notes, design-review support, and post-arrival assistance. The fixed price is [your fixed price], with delivery in [your timeline]. I am ready to turn your existing prototype into a compact, manufacturable board while keeping RF, power integrity, wearability, and future medical-device good practice in focus. Thanks!


Designing compact RF hardware is my core strength: I am a senior electronics engineer with over 8 years of experience in RF engineering, embedded systems, circuit design and PCB layout. That background directly matches your wearable’s demanding combination of nRF9160 LTE-M/GNSS, ESP32-S3, constrained antenna space and battery-powered operation. I can develop the V1 schematic and compact four-layer layout while considering radio peak currents, power distribution, charging safety, ESD protection, sensor placement and two-sided assembly. My experience covers RF modules, embedded controllers, power converters and complete hardware delivery from design and simulation through validation and documentation. I can provide the editable design source, Gerbers, BOM, CPL, assembled-board STEP model, power budget and antenna tuning notes required for JLCPCB. I would be pleased to contribute to this safety-focused wearable and support a professional, certification-conscious first prototype. My fixed price, timeline, design-review call and post-arrival support can be agreed within the project scope.


Hi there, Do you want the first pass focused on KiCad or EasyEDA, and is there a preferred stack-up for the 4-layer board? Do you want the first pass focused on KiCad or EasyEDA, and is there a preferred stack-up for the 4-layer board? The main challenge here is fitting LTE, GNSS, audio, sensing, and power into a very small wearable while keeping the radio layout stable. A good approach is to start with the power tree and antenna keep-outs, then build the schematic and floorplan around the RF and skin-contact sensor areas. The biggest risk is LTE and GNSS performance on a tight board near batteries, speakers, and a waterproof enclosure. That needs careful antenna placement, controlled return paths, ESD protection, and a solid tuning plan before release. Can support the full V1 package for JLCPCB assembly, including schematic, PCB layout, BOM, CPL, Gerbers, STEP, power budget, and antenna notes. A design review call is fine, and post-arrival support can cover bring-up, assembly issues, and early test adjustments. Best, Hlib


Hello, My expertise in circuit design, electronics, and PCB layout aligns directly with creating a compact prototype board from your existing wearable design. I can develop clear, fabrication-ready documentation for the ESP32-S3, nRF9160, PPG sensor, power system, audio, charging, and supporting circuitry, with close attention to the tight 38 × 34 mm board area and two-sided assembly. As a Licensed Professional Engineer, I bring a documentation-focused engineering approach suited to a product intended for later certification. My broader design experience includes mechanical/product CAD, fabrication drawings, MEP coordination, and engineering calculation packages, which supports producing organized source files, drawings, schedules, and manufacturing documentation. My electronics and PCB Layout skills are relevant to the schematic, board layout, BOM, Gerbers, and CPL deliverables. I can provide a fixed price and timeline after reviewing the attached specification; cellular-module and antenna examples, KiCad/EasyEDA experience, and post-assembly review support are not included in my listed profile, so I will not misrepresent them. Select me for disciplined engineering documentation and a practical, buildable prototype design. Thanks!
内容来自 Freelancer News,版权归原作者所有。
阅读原文 ↗