ESP32 Irrigation Controller PCB Design
$30-250 USD
Posted 1 minute ago
•
Ends in 6 days
$30-250 USD
Paid on delivery
Important : We will only accept proposals that fall within our budget range (fixed price). If you have a different budget expectation, please do not submit a proposal. Project Description : Design the schematic and PCB for one irrigation controller. This is a hardware design job. Firmware is not included. The controller runs from 24 V DC. The MCU is fixed: Espressif ESP32-WROOM-32UE, external antenna, [login to view URL], at least 4 MB flash. Not a module with a PCB antenna, and not a development board. The board has wired 10/100 Ethernet and USB-C programming. Inputs: 3 float switches, 3 NPN level sensors, 2 pressure transducers, 1 pulse flow meter, and 1 two-wire leak probe. Outputs: 6 low-side MOSFET channels (2 solenoids, 1 irrigation pump, 1 mix pump, 2 low-current spares). A load may be 12 V, 24 V, or 48 V. Only the irrigation pump reaches 10 A. The load positive is terminated off the PCB. The board switches the return only, and the MOSFET must be rated for a 48 V inductive load. One RGB status LED is driven by three GPIOs. Each output and each float input has its own green indicator, and the leak input has one. Indicators are steady on/off, not a blink pattern. The enclosure drawing, three PCB size options, and a connection diagram will be sent privately to the selected freelancer. Fit the smallest outline that holds the circuit. Do not invent the board size. The concept diagram was drawn by the client, who is not an electronics engineer. It states the equipment and the intended connections. You are responsible for the schematic, the parts, and every technical detail, including the pins drawn on that diagram. PCB finish: matte black solder mask, white silkscreen. Every screw is labelled with the equipment and the pin function. One screw-terminal family for all field wiring. No push-in terminals. Mounting holes are Ø3.2 mm for M3, with an annular pad and a ring of vias. Preferred CAD is KiCad. Another CAD tool is acceptable if the source, a PDF schematic, and standard Gerbers are delivered. Deliverables: schematic and PDF, PCB source, GPIO and connector map, BOM with manufacturer and distributor codes, Gerbers, drill, pick-and-place, assembly PDF, and a short design note. Review gates: schematic and pin map, then placement, then Gerbers. Out of scope: firmware, enclosure machining, cable manufacturing, and certification testing.
Project ID: 40810028
About the project
7 proposals
Open for bidding
Remote project
Active 5 secs ago
Place your bid
Bid amount Email addressBenefits of bidding on Freelancer
Set your budget and timeframe
It's free to sign up and bid on jobs
7 freelancers are bidding on average $152 USD for this job


Hello, Industrial automation and embedded hardware development have been the focus of my electronics engineering work for more than 10 years, including sensor interfaces, power electronics, machine controllers, and complete PCB development. That background directly matches your irrigation controller’s mixed field inputs, ESP32-based control, Ethernet/USB-C connectivity, and MOSFET-switched industrial loads. I can take responsibility for the schematic, component selection, footprints, multilayer PCB layout, protection, connector labeling, and manufacturing documentation. My experience with ESP32, analog and digital electronics, sensors and ADC systems, relays, power supplies, motor/actuator integration, and DFM is relevant to handling the 24 V supply, 48 V inductive-load-rated output stages, 10 A pump channel, indicators, and varied field wiring. I also work across the complete hardware cycle from concept through prototyping, troubleshooting, commissioning, and small-batch manufacturing documentation. I am ready to deliver the KiCad source and the requested schematic, pin map, BOM, Gerbers, drill files, pick-and-place, assembly PDF, and design note through the defined review gates. Choose me for a practical industrial PCB design focused on electrical correctness and manufacturability. Thanks!


Hi - Adelman here from Texas ESP32 IRRIGATION CONTROLLER PCB DESIGN - you need a reliable 24V controller with 48V inductive-load switching, wired Ethernet, and clearly mapped field connections. I'd approach this with a KiCad schematic first, carefully checking GPIO allocation, input conditioning, power regulation, and MOSFET protection before PCB placement. The 10A pump channel and 48V inductive loads need particular attention to component ratings, heat, and flyback protection. I'll follow your three review gates and deliver the complete PCB source, BOM, Gerbers, assembly files, and documentation. Firmware is excluded as requested. Can you confirm the electrical specifications and output current requirements for the two solenoids and mix pump? Looking forward to work with you.


Hi there, Can the 48 V inductive load use the same switching topology as the 24 V channels, or should it get a separate protection stage? Can the 48 V inductive load use the same switching topology as the 24 V channels, or should it get a separate protection stage? Can the 48 V inductive load use the same switching topology as the 24 V channels, or should it get a separate protection stage? For the Ethernet and USB-C sections, do you want any specific ESD, isolation, or connector placement constraints from the enclosure? The main challenge is fitting the ESP32-WROOM-32UE, Ethernet, USB-C programming, and mixed industrial I/O into the smallest outline without noise issues. A clean approach is a layered schematic with isolated input conditioning where needed, proper MOSFET gate drive and flyback paths, then a placement-first PCB pass around the enclosure limits and field wiring paths. The biggest risk is interference from the pumps, solenoids, and sensors sharing one 24 V system. That is usually handled by partitioning the board into power, digital, and field I/O zones, then checking return paths, transients, and connector pinout before routing is frozen. Can prepare the schematic, pin map, BOM, and PCB source in KiCad, then move through your review gates: schematic, placement, and Gerbers. Testing will focus on design-rule checks, net-by-net review, and assembly-ready outputs with clear labels for every screw terminal and indicator. Best, Hlib


The parts that need the most care here are the 10 A pump path and the 48 V inductive turn-off. I'll size the copper and pick MOSFETs with enough margin, add flyback and TVS protection options for the return-only switching, and sanity-check every pin on your diagram before layout. You'll get the full package you listed, in KiCad, through your three review gates. I've done a lot of industrial control boards, motor drivers and ESP32/STM32 designs, and some PCB work is in my portfolio. Delivery in about 10 days.


Hello Mate!Greetings , Good evening! I am an expert electronics engineer with skills including PCB Layout, Embedded Systems, Microcontroller Programming (STM32 / ESP32), Circuit Design, C Programming, Prototyping, Electronic Design, Microcontroller and Electronics. I am checking your attachment, I'll update you shortly... Please contact me to discuss more about this project. Best Regards


✅ Hey Mate✅ , Good afternoon! I am an expert engineer with skills including Microcontroller, Embedded Systems, Electronic Design, Prototyping, C Programming, PCB Layout, Circuit Design, Microcontroller Programming (STM32 / ESP32) and Electronics. Recently, I've done similar project so I am very confident to start your project. I can review your project requirements, understand the technical challenges, and develop a practical and cost-effective solution that meets your specifications. I focus on accuracy, quality, clear communication, and delivering work within the agreed timeline. I would be happy to discuss your project in more detail, understand your expectations, and explain how I can contribute to its successful completion. Please message me here so we can discuss the details. Best regards,
内容来自 Freelancer News,版权归原作者所有。
阅读原文 ↗