PCM Heat Exchanger Melting Simulation
₹12500-37500 INR
Posted 1 minute ago
•
Ends in 6 days
₹12500-37500 INR
Paid on delivery
I am looking for a complete numerical model that captures how quickly the phase-change material (PCM) inside a latent-heat storage unit melts and solidifies when heat-transfer fluid flows through several parallel tubes. The geometry is a tube-in-PCM heat exchanger, not a packed bed or single straight tube, so please centre your approach on that configuration. What matters most is an accurate, transient prediction of the melt/solidification front, local temperatures and the energy stored or released over time. The final model should let me vary tube-side inlet temperature, flow rate and PCM properties so that I can explore different operating scenarios later without rewriting the code. Please choose whatever CFD or numerical platform you are most comfortable with—ANSYS Fluent, COMSOL, OpenFOAM, custom Python/FORTRAN with an enthalpy method, etc.—as long as the phase-change physics are treated properly and the results can be regenerated on my end. Document all assumptions, boundary conditions and material data you use. Deliverables • Simulation setup files and source code • Clear instructions for rerunning and modifying the case • A brief report summarising model formulation, verification steps and key plots (temperature fields, melt/freeze fraction vs. time, energy stored) I will review the work by re-running the case, checking that the melt/freeze times match the report and confirming that parameter changes produce physically reasonable trends. If you can meet these points, I’m ready to get started.
Project ID: 40809413
About the project
3 proposals
Open for bidding
Remote project
Active 20 secs ago
Place your bid
Bid amount Email addressBenefits of bidding on Freelancer
Set your budget and timeframe
It's free to sign up and bid on jobs
3 freelancers are bidding on average ₹19,280 INR for this job


Hello, You're looking for a transient numerical model of a tube-in-PCM heat exchanger that accurately predicts melt/solidification fronts, local temperatures, and energy storage/release over time. The tricky part here is ensuring the phase-change physics are treated correctly while keeping the model flexible enough to handle varying inlet temperatures, flow rates, and PCM properties without requiring major code changes. I'd start by setting up the geometry and defining the boundary conditions in COMSOL, since it handles phase-change problems well and allows for easy parameter variation later. I'd use the enthalpy method to capture the phase-change dynamics and verify the model against known benchmarks for accuracy. Once the base case is stable, I'd document the setup thoroughly and write clear instructions for modifying parameters so you can explore different scenarios independently. I delivered a similar project last month, a transient heat transfer model for a thermal energy storage system using phase-change materials. Do you have specific PCM properties or tube geometries in mind, or should I use generic values for the initial setup?


Hi, I’d first build a transient tube-in-PCM model with an enthalpy-based phase-change formulation, because it can track the moving melt/freeze front and stored energy without restricting the geometry to a single tube or packed bed. I’ll represent the parallel tube flow and PCM heat transfer with coupled fluid and solid energy equations, including temperature-dependent properties and latent heat through an enthalpy or apparent-heat-capacity method. Tube inlet temperature and flow rate, PCM data, tube layout, and initial conditions will be exposed as parameters. I’ll provide the source code and setup files, then generate temperature fields, liquid fraction versus time, and stored/released energy plots. Verification will include mesh and time-step checks, energy-balance checks, reruns of the supplied case, and parameter changes to confirm physically sensible trends. The results will depend strongly on PCM thermophysical data, contact resistance, tube spacing, and the selected phase-change temperature range. I’ll document these assumptions and boundary conditions clearly, and I’ll flag any missing geometry or material data before finalizing the model so your rerun matches the reported melt and solidification times. Thank you


I’ll build a fully transient PCM melt‑freeze model in COMSOL, using an enthalpy‑method with adaptive mesh refinement to capture the moving interface accurately. The ready‑to‑run setup lets you vary inlet temperature, flow rate, and PCM properties effortlessly. I’ll provide full files, a user guide, and a concise validation report.
内容来自 Freelancer News,版权归原作者所有。
阅读原文 ↗