Dongle/USB Kit (LoRa Receiver) — PCB Design & Production -- 2

$30-250 CAD

Posted 1 minute ago

•

Ends in 6 days

$30-250 CAD

Paid on delivery

I need a production-ready USB dongle that can sit in any laptop or desktop port and act as the single receiver for a fleet of wearable Collector Kits. The core requirements are: • Frequency: the RF front-end must operate on 868 MHz or 915 MHz so the same board can be stuffed for either region. • Power: the board is strictly bus-powered; no external barrel jack or battery input. • Capacity: it has to listen to, and reliably demodulate, traffic from roughly 25 simultaneous Collector Kits before forwarding the raw payloads to the host over a simple USB-CDC (UART) stream. This is a ground-up, chip-level design. Place the transceiver IC, MCU/USB bridge, matching network, crystal, ESD protection, and supporting passives directly on the PCB—no breakout modules or dev boards. Careful RF layout, impedance control, and enclosure clearance are essential to keep the finished stick compact and professional, similar in size to a commercial Wi-Fi dongle. Deliverables 1. KiCad Schematic, Optimised 1- or 2-layer PCB layout with manufacturing notes 2. Complete production files BOM with sourcing links, Gerber/ODB++ files, pick-and-place, and assembly drawing 3. Assist in ordering in the manufacturer's portal (JLCPCB, PCBWay, etc.) for 5 samples. 4. Technical documentation I will handle regulatory certification later, but please keep ETSI/FCC guidelines in mind during the design so we are not forced into major re-spins. If you have prior LoRa RF experience and can quickly turn a neat, manufacturable USB stick, let’s talk.

Project ID: 40807948

About the project

4 proposals

Open for bidding

Remote project

Active 21 secs ago

Place your bid

Bid amount Email address

Benefits of bidding on Freelancer

Set your budget and timeframe

It's free to sign up and bid on jobs

4 freelancers are bidding on average $146 CAD for this job

User Avatar
Flag of UKRAINE

Hello, Over 15 years in electronic hardware and firmware engineering makes me well suited to develop your production-ready LoRa USB receiver from schematic through manufacturing files. My experience includes complex PCB layouts, embedded systems, IoT solutions, and taking designs from concept to production, directly matching your need for a compact, manufacturable dongle rather than a module-based prototype. I work with KiCad, Altium Designer, and Eagle, and can design the chip-level circuit around the transceiver, MCU/USB interface, power protection, crystal, passives, and RF section. My STM32, ARM Cortex, C/C++, SPI, UART, and signal-processing experience supports reliable USB-CDC payload forwarding and embedded firmware integration. PCB layout and electrical engineering expertise also allows careful attention to impedance-controlled RF routing, grounding, ESD protection, bus-only power, and production documentation. I can provide the schematic, optimized PCB layout, BOM with sourcing links, Gerber/ODB++ files, pick-and-place data, assembly drawings, manufacturing notes, and technical documentation, while supporting the sample order process. I am ready to apply my production-focused hardware experience to your 868/915 MHz receiver and deliver a professional design prepared for manufacturing. Thanks!

User Avatar
Flag of UNITED STATES

Hello, My Electrical Engineering background and Licensed Professional Engineer credentials support disciplined, code-conscious design documentation for technical hardware projects. I can prepare clear engineering drawings, manufacturing notes, technical reports, and coordinated documentation with careful attention to specifications and regulatory considerations. For this USB LoRa receiver, I can contribute to the schematic and PCB documentation, component and BOM organization, production-file preparation, assembly documentation, and manufacturer-portal coordination. My experience producing precise construction and engineering packages in AutoCAD, Autodesk Revit, and related design tools translates well to maintaining organized, reviewable deliverables and ensuring the design package is suitable for fabrication and assembly. I would be glad to support your dongle project with professional Electrical Engineering documentation and a strong focus on manufacturability and compliance awareness. Thanks!

User Avatar
Flag of UNITED STATES

Hello, My Electrical Engineering background and experience producing detailed, manufacturable engineering documentation can support the PCB design and production package for your USB LoRa receiver. I can develop the KiCad schematic and compact PCB layout around the required bus-powered architecture, including the transceiver, MCU/USB interface, crystal, matching network, ESD protection, and supporting passives. I will also prepare manufacturing documentation such as the BOM, sourcing information, Gerber/ODB++ files, pick-and-place data, assembly drawings, and technical notes, while keeping RF layout, impedance control, USB integration, enclosure clearance, and ETSI/FCC considerations in focus. My broader engineering and CAD experience, including SolidWorks and Fusion 360, is useful for maintaining a practical, professional dongle form factor. I would be glad to provide a complete production-oriented design package and assist with the manufacturer portal and five-sample order. Thanks!

内容来自 Freelancer News,版权归原作者所有。

阅读原文 ↗

把喜欢的内容,留在你的新标签页。

打开我的订阅