Smart BMS + External Cell Balancer for 12S-18S LiPo / LiHV Packs (PCB + Firmware)
₹75000-100000 INR
Posted 1 minute ago
•
Ends in 6 days
₹75000-100000 INR
Paid on delivery
PLEASE READ BEFORE YOU BID - Read this post and both attached spec PDFs fully before you bid. - We are looking for PCB designers. BMS experience is a big plus. - In your bid, give a short basic understanding of this project in your own words. - Bids with general text will not be selected. The project We need a BMS for our own 12S, 14S and 18S LiPo / LiHV battery packs (cells up to 30 Ah, pack 30-80 V). This is 1 project with 2 PCB works. A detailed spec PDF for each work is attached. Work 1: BMS board + optional cut-off module (inside the pack) - Monitors every cell (≤10 mV) and measures current through an off-board shunt (0.5-400 A, no overflow to 800 A for 3 s). - Balances at about 100 mA per cell, counts charge, keeps a log, shows charge on 5 green LEDs. - Talks over isolated CAN (DroneCAN), plus Bluetooth on one model. - USB port (micro USB, USB-C or similar) to write firmware and copy logs / data to a PC. - No pack current flows through the board. One PCB makes all models by fitting or leaving out parts. - An optional cut-off module plugs into the board: - 363 A continuous, 800 A for 3 s, 150 A charge - pre-charge and a hardware short-circuit trip - it never cuts flight power except on a short Work 2: External cell balancer (at the charging place) - 18 channels at about 1 A per cell, each switched on its own; heat stays outside the pack. - USB port (micro USB, USB-C or similar) to write firmware and copy logs / data to a PC. - Two modes, chosen by which input the pack is plugged into: - BMS mode: our BMS controls it over CAN and an enable pin. - Standalone mode: it serves other packs through a standard balance lead, with its own ≤10 mV readings, cell count check and stops. The two works share the balance connector, the enable pin and the CAN message set, so one designer keeps them matched. Deliverables for each work - Schematic, PCB, BOM and Gerbers. - Full firmware source with build steps. - Protocol documents (Bluetooth / CAN; balancer messages). - A PC tool for testing, firmware writing and log / data copy over USB. - Test and calibration procedure, and a test report. You choose all parts: branded, with steady supply and a datasheet. In your bid, tell us 1. Your basic understanding of this project, in your own words. 2. Your PCB design experience, with 2-3 boards you designed (pictures or links). 3. Your plan and time for Work 1 and for Work 2. 4. Any question you have about the spec.
Project ID: 40806543
About the project
1 proposal
Open for bidding
Remote project
Active 21 secs ago
Place your bid
Bid amount Email addressBenefits of bidding on Freelancer
Set your budget and timeframe
It's free to sign up and bid on jobs
1 freelancer is bidding on average ₹78,000 INR for this job


Two boards that share one balance connector, enable pin and CAN message set: a BMS with 10 mV cell readings, shunt current sensing, isolated DroneCAN and USB, plus a plug-in cut-off module; and an 18-channel 1 A external balancer that runs under BMS control or standalone. The hard parts are heat in the balancer, the 800 A shunt range and the hardware short-circuit trip. I've built multi-cell Li-ion protection boards, STM32 boards with isolated CAN, and Python USB tools. Some of that is in my portfolio. Plan: Work 1 in about 4 weeks, Work 2 in about 3, overlapping, with firmware, docs and test report included. Should the cut-off module use MOSFETs or a contactor?
内容来自 Freelancer News,版权归原作者所有。
阅读原文 ↗