CNC Pocket Test G-Code
$10-30 USD
Posted 1 minute ago
•
Ends in 6 days
$10-30 USD
Paid on delivery
I’m getting my CNC router dialed in and need a quick test gcode file created using VCarve Pro 11.0: A simple 3" square toolpath that clears a 1" pocket in a piece of 1.5" HDU foam. No through-cuts—just enough depth to verify accuracy, step-over, and machine tuning. For this test I need the bit to first run a complete outline of the square then clear the inside 1/4" down in a horizontal (X axis) direction, then the second pass 1/4" lower to run a complete outline of the square again then clear the inside in a vertical pass (Y axis), 3 pass in the X axis and last pass in the Y axis. Feel free to suggest feeds, speeds, and step-downs for a typical ¼-inch ballend mill in HDU, and include them in the header so I can tweak if necessary. Tools and Equipment: Two Trees 6050: [login to view URL] Ballnose Bit used: [login to view URL] Deliverables • One ready-to-run .gcode (or .nc) file for the rectangular pocket • Datum position: Front Left. • Z position: Surface • Spindle speed prefered 12,000 max. • VCarve 11.0 file • A short note listing cutter size, pocket depth, feed/speed values, and overall pocket dimensions I’ll load the file, run it, measure the pocket, and release payment once it cuts cleanly and the rectangle is square within expected tolerances.
Project ID: 40830446
About the project
5 proposals
Open for bidding
Remote project
Active 6 secs ago
Place your bid
Bid amount Email addressBenefits of bidding on Freelancer
Set your budget and timeframe
It's free to sign up and bid on jobs
5 freelancers are bidding on average $24 USD for this job


I'll build the test toolpath for your 3 in square outline and 1 in pocket in 1.5 in HDU, following your sequence: outline and X-axis clearing at the first depth, then the outline again 1/4 in lower with Y-axis clearing. Feeds, speeds and step-downs for a 1/4 in ball nose will be in the header so you can tune them. Quick check: is the pocket 1 in across, or the 3 in square outline with the 1 in pocket inside it? You'll get the ready-to-run .nc file with datum at front left and Z zero at the surface, the native project file, and a short note with cutter size, depth, feeds, speeds and pocket dimensions. I'll also check the square geometry in the file before sending it. Ready to start right away. Thanks!


I'll set up the 3 in. square pocket toolpath for your 1 in. test cut in 1.5 in. HDU, using the 1/4 in. ball nose outline passes, the two 1/4 in. stepdowns and the X-then-Y clearing sequence you described. Feeds, speeds, stepdown and the Front Left datum will be written in the header so you can tweak them before running. You'll get one ready-to-run .gcode file plus a short note with cutter size, depth, feed/speed values and final pocket dimensions. Since I work in CAD and CNC-ready models, I'll also check the square outline dimensions in the output before sending. Ready to start right away. Thanks!


Hi there, Your alternating X/Y pocket test is a practical way to check squareness and cutting behavior. I’m an Engineer with 10+ years of engineering experience. I can organize the 3-inch square outline and staged pocketing sequence into a clearly documented test, with editable feed, speed, and step-down notes and no through-cuts. VCarve Pro 11.0 isn’t among my listed tools, so I would familiarize myself with it and confirm the output postprocessor matches your Two Trees controller before treating the file as ready to run. Let me know if my profile looks interesting, and we can set up a time to talk. Best regards, Vadym P.


Hi there, Your Two Trees 6050 pocket test needs clearly sequenced outline and X/Y clearing passes, with conservative settings for HDU and no through-cuts. I’m a CNC/CAD professional and would tailor the file and setup note to your front-left datum, surface Z, 12,000 RPM limit, and requested pass sequence. VCarve Pro 11.0 is not listed among my current tools, so I would first learn the required workflow rather than claim prior experience with it. I can document the ¼-inch cutter, ½-inch pocket depth, suggested feeds and speeds, and 3-inch square dimensions for your review. Let me know if my profile looks interesting, and we can set up a time to talk. Best regards, Robert W.
内容来自 Freelancer News,版权归原作者所有。
阅读原文 ↗