Compact BLE 5.4 RF PCB Design

₹3000-5000 INR

₹3000-5000 INR

Paid on delivery

Job Title: Compact 2-Layer BLE 5.4 PCB Layout (Telink TL3218FE10T28R QFN-28 + 2.4GHz MIFA Trace Antenna) Project Description: Looking for an experienced RF/embedded PCB designer to create the schematic and 2-layer PCB layout for a compact, ultra-thin BLE 5.4 wireless tag based on the Telink TL3218FE10T28R (QFN-28, 3.5 × 3.5 mm) SoC. A complete hardware specification PDF with reference schematic, BOM, floorplan, and RF routing guidelines will be provided upon selection. Key Hardware & Layout Specifications: • Board Dimensions & Stackup: 16.5 mm × 31.0 mm, 2-layer FR-4, 0.8 mm (or 0.6 mm) thickness, ENIG surface finish, 1.0 mm rounded corners. • Core Components (Single-Sided SMD Assembly): • Telink TL3218FE10T28R (QFN-28, 0.4 mm pitch) • 24.000 MHz crystal (1612 package, uses internal load caps) • 2.2 µH DC-DC buck inductor (0402), L-matching network (C6, L2 in 0402), and decoupling capacitors (0402) • 0603 right-angle (side-emitting) green LED + series resistor on PA0 • 3 bare ENIG pogo-pin test pads (SWS, VBAT, GND) on the bottom side • Mechanical Battery Cutout: Milled Ø 12.5 mm circular cutout in the bottom zone flanked by 2.0 mm side rails, paired with a low-profile 12 mm SMD coin-cell retainer footprint (Keystone 3000 or equivalent) for CR1216/CR1220 cells. • RF & Antenna Requirements: • Top 6.0 × 16.5 mm strict keep-out zone (no ground copper on either layer) with a 2.45 GHz Meandered Inverted-F Antenna (MIFA) printed on the top layer. • 50 Ω Grounded Coplanar Waveguide (GCPW) feed line (0.95 mm trace / 0.25 mm gap for 0.8 mm FR-4, or 0.75 mm / 0.25 mm for 0.6 mm FR-4) with ground stitching via fencing. • Continuous bottom ground counterpoise and 3×3 thermal/ground via array under the QFN-28 exposed pad. • Pinout Verification: Designer must verify all QFN-28 pin assignments against the official Telink TL321X Datasheet / Hardware Design Guideline prior to routing. Required Deliverables: 1. Native EDA source files (KiCad or EasyEDA Pro preferred; Altium acceptable) 2. Fabrication-ready Gerber files & NC Drill files (including internal cutout milling layer) 3. Pick-and-Place (CPL/POS) file and verified BOM 4. 3D STEP model and PDF schematic/assembly drawings To Apply, Please Share: • 1–2 examples of past 2.4 GHz BLE/RF PCBs with printed trace or chip antennas you have designed. • Which EDA tool you will use (KiCad / EasyEDA / Altium) and your estimated turnaround time.

Project ID: 40830371

About the project

5 proposals

Remote project

Active 1 min ago

Looking to make some money?

Email address

Benefits of bidding on Freelancer

Set your budget and timeframe

It's free to sign up and bid on jobs

User Avatar
Flag of VIETNAM

Hi, I’m a PCB Design Engineer with experience in Japanese engineering projects, wireless hardware, ESP32, CC1101, LoRa, RF matching networks, and multilayer PCB design. I can handle the complete schematic and 2-layer PCB layout for your BLE 5.4 tag. My workflow will include: 1. Verify the TL3218FE10T28R QFN-28 pinout against the official Telink datasheet and hardware guidelines. 2. Develop the schematic, including power management, 24 MHz crystal, decoupling, LED, and programming interface. 3. Design compact component placement within the 16.5 × 31 mm board constraints, including the battery holder and mechanical cutout. 4. Implement the 2.45 GHz MIFA antenna, 50-ohm GCPW feed, matching network, ground keepout, and via fencing. 5. Perform ERC/DRC checks, 3D mechanical verification, and prepare manufacturing files. I can work with KiCad or Altium Designer and deliver native project files, Gerbers, NC Drill, milling data, BOM, CPL, STEP model, and PDF drawings. Estimated turnaround: 6–8 working days after receiving the complete specifications. I would be glad to review your reference documents and discuss the technical details before starting. Best regards.

5 freelancers are bidding on average ₹5,400 INR for this job

User Avatar
Flag of PAKISTAN

I am an Embedded Systems and PCB Design Engineer with experience in Altium Designer, Kicad, Easyeda, Protious and custom hardware development. I can design your PCB from schematic to production-ready files, including: • Schematic Design • PCB Layout • Component Selection • Design Rule Check (DRC) • Gerber Generation • BOM Preparation • Manufacturing Support (JLCPCB, PCBWay, etc.) I have experience with ESP32, STM32, sensor interfaces, power supplies, RF modules, Ethernet, and industrial electronics. Please share the project requirements, schematic (if available), board dimensions, and any special requirements. I can start immediately. Looking forward to working with you.

User Avatar
Flag of NEPAL

Hello, I am Santosh Chaulagain, a professional Electrical Engineer and PCB Designer with over 7 years of experience in schematic design, PCB layout, and embedded systems, including ESP32, IoT devices, analog and digital circuits. I have successfully completed multiple projects for clients worldwide, delivering reliable and manufacturable designs. I have carefully reviewed your project requirements and I am confident that I can provide a high-quality solution tailored to your needs. My expertise includes PCB design using industry standards, component selection, BOM preparation, Gerber generation, and design optimization for cost and performance. I always ensure that my designs are fabrication-ready and tested for reliability. I focus on clear communication, timely delivery, and customer satisfaction. I am happy to discuss your project in detail and provide revisions until the final result meets your expectations. Looking forward to working with you. Best regards, Santosh C. Electrical Engineer | PCB Designer | ESP32 & IoT Specialist

User Avatar
Flag of VIETNAM

I can design your 16.5 × 31.0 mm BLE tag in KiCad. My background spans embedded system design, RF PCB layout, and firmware development. On a board this small, I’d review the antenna, coin-cell cutout, and retainer footprint together before routing. I’ll verify the TL3218FE10T28R pinout and exposed pad against Telink’s official documentation. For the 2.45 GHz MIFA, I’ll preserve the 6 mm antenna keep-out on both layers, check the 50 Ω feed geometry against the fabricator’s stackup, and leave the matching components accessible for prototype tuning. I’ll also check the 2 mm side rails, single-sided assembly, and bottom pogo-pad access in the layout and STEP model. I’ll deliver the native KiCad files, Gerbers, NC drills and cutout milling data, verified BOM, pick-and-place file, STEP model, and schematic and assembly PDFs. Estimated turnaround: 5–7 business days after receiving the hardware specification and confirming the stackup, with a placement review before routing. Best regards.

User Avatar
Flag of SRI LANKA

Hello, Please see my previous design, CC3235S Custom Development Board: https://www.freelancer.com/u/malindu0027 I can use KiCad and EasyEDA depending on your preference. looking forward to working with you. Thank You.

内容来自 Freelancer News,版权归原作者所有。

阅读原文 ↗

用 HomepageTab 新标签页关注 RSS,打开浏览器就能看到更新。

安装 HomepageTab