Cleanroom CFD Airflow Optimization

$2000-7000 SGD

Posted 1 minute ago

•

Ends in 6 days

$2000-7000 SGD

Paid on delivery

CFD Simulation and Airflow Optimization for Cleanroom 1A and 2A Computational Fluid Dynamics Study • Cleanroom 1A (3,450 m²) • Cleanroom 2A (1,000 m²) TYPE TOTAL AREA DURATION BUDGET 1. Project Overview We require a detailed Computational Fluid Dynamics (CFD) study for two cleanrooms only: Cleanroom 1A and Cleanroom 2A. No other areas are in scope. The goal is to validate and optimize temperature uniformity, humidity control, airflow distribution, and return air performance before final design freeze and commissioning. The system uses a combination of AHU supply air, FFU array, return air chase, and dry coils. The CFD must model the interaction between all four, not each in isolation. 2. Scope of Work Scope is strictly limited to the two cleanrooms below. Out of scope: all other cleanrooms, corridors, sub-fab, and mechanical rooms, unless they directly affect return air or plenum pressure for 1A / 2A. Cleanroom Area Scope Cleanroom 1A 3,450 m² Full CFD model, analysis, and recommendations Cleanroom 2A 1,000 m² Full CFD model, analysis, and recommendations 3. Key Parameters to Model The simulation must explicitly include these four inputs. Proposals that do not address all four will not be considered. 3.1 Return Air Temperature Distribution: Model return air temperature distribution across the cleanroom and at each return air inlet. Stratification: Assess stratification, hot spots, and temperature rise from process heat loads. AHU return: Predict return air temperature back to the AHU under design and partial load conditions. Load impact: Quantify impact on cooling load and AHU energy. 3.2 Location of Return Air Chase and Dry Coil Chase and coil location: Model the proposed location(s) of the return air chase and dry coil(s). Pressure and capture: Evaluate pressure drop, airflow short-circuiting, and uniformity of return air capture. Dry coil duty: Assess dry coil performance for sensible cooling and temperature trim without condensation. Optimization: Recommend optimized location, sizing, or relocation if the current layout creates dead zones, recirculation, or uneven return. 3.3 Direct Supply Air Diffuser Location Above Plenum AHU condition: AHU with 8 °C coil, providing both cooling and dehumidification. Plenum and diffusers: Model supply air plenum above the ceiling and all direct supply air diffusers fed by the AHU. Psychrometrics: Model supply air temperature, humidity ratio, and dew point after the 8 °C coil. Diffuser performance: Evaluate diffuser throw, plenum pressure uniformity, velocity at working plane, and interaction with FFU flow. Risk check: Identify over-cooling, condensation risk, or humidity non-uniformity. 3.4 All FFU Locations and Flow Rates Every FFU: Model every FFU by its exact location and rated flow rate / face velocity from the FFU schedule. Scenarios: Include FFU on/off scenarios and turndown if applicable. Coverage: Evaluate coverage, overlapping flows, downward velocity uniformity, and turbulence at process level. Interaction: Evaluate interaction between FFU downflow, AHU diffuser supply, and return air chase. 4. Analysis Required Steady-state + partial load: Steady-state simulation at full design load, plus at least one partial load / standby scenario. Humidity: Relative humidity / humidity ratio distribution resulting from the 8 °C coil dehumidification. Airflow: Velocity vectors, streamlines, and air change effectiveness. Problem zones: Identification of dead zones, recirculation zones, short-circuiting, and hot spots. Pressure profile: Pressure across plenum, cleanroom, return chase, and dry coil. Quality checks: Mesh independence study and convergence report. Sensitivity check: What happens if FFU flow varies by +/- 10%, or if one return chase is blocked / one dry coil is off? 5. Deliverables 1. CFD Report (PDF): Methodology, assumptions, boundary conditions, mesh study, results, and clear design recommendations. 2. Contour and Vector Plots: Temperature, humidity, velocity, and pressure for 1A and 2A, plan and section views. 3. Streamline / Animation: Airflow path from supply diffusers and FFUs to return chase. 4. Summary Table: Predicted temperature uniformity, max/min temperature at working plane, return air temperature, RH range, and velocity uniformity for each cleanroom. 5. Recommendations: Specific changes to diffuser location, return chase location, dry coil location, or FFU flow rates if targets are not met. 6. Native Case Files: [ANSYS Fluent / CFX / OpenFOAM / Star-CCM+ - specify your software] with all boundary conditions, so we can rerun or audit. 6. Inputs We Will Provide Architectural and HVAC layout drawings for 1A and 2A (CAD / PDF / Revit if available) Ceiling plan with FFU layout and FFU schedule with flow rate per unit AHU schedule, including 8 °C coil specs, supply air flow rate, supply temperature, and dehumidification duty Diffuser schedule, location, and throw data Return air chase and dry coil drawings and specs Internal heat loads: equipment, lighting, personnel, process tools Target conditions: [e.g. Temp 22 °C +/- 1 °C, RH 45% +/- 5%, Cleanroom Class ISO 6, Velocity 0.3 to 0.45 m/s - to be confirmed] Plenum height, ceiling height, and floor layout 7. Freelancer Requirements Proven experience in cleanroom CFD, preferably semiconductor, pharma, battery, or microelectronics facilities Expert in ANSYS Fluent, CFX, Star-CCM+, or OpenFOAM, with examples of similar cleanroom projects Strong understanding of AHU psychrometrics, dehumidification with chilled water coil, FFU systems, and dry coil operation Able to work from CAD / Revit and FFU schedules Able to sign NDA before receiving detailed drawings

Project ID: 40828829

About the project

2 proposals

Open for bidding

Remote project

Active 11 secs ago

Place your bid

Bid amount Email address

Benefits of bidding on Freelancer

Set your budget and timeframe

It's free to sign up and bid on jobs

2 freelancers are bidding on average $3,998 SGD for this job

User Avatar
Flag of POLAND

✅ Hi There✅ , Good afternoon! I am professional engineer with skills including Computational Fluid Dynamics, Simulation and Clean Technology. Recently, I've done similar project so I am very confident to start your project. I can review your project requirements, understand the technical challenges, and develop a practical and cost-effective solution that meets your specifications. I focus on accuracy, quality, clear communication, and delivering work within the agreed timeline. I would be happy to discuss your project in more detail, understand your expectations, and explain how I can contribute to its successful completion. Please message me here so we can discuss the details. Best regards,

内容来自 Freelancer News,版权归原作者所有。

阅读原文 ↗

用 HomepageTab 新标签页关注 RSS,打开浏览器就能看到更新。

安装 HomepageTab