Hardware/PCB Engineer Needed – ESP32 Startup & W5500 Ethernet Reliability (EasyEDA Pro)
$10-30 USD
Posted 1 minute ago
•
Ends in 6 days
$10-30 USD
Paid on delivery
I have designed and manufactured a custom PCB using an ESP32-WROOM-32 and W5500 Ethernet module in EasyEDA Pro. The PCB works, but I am experiencing intermittent hardware reliability issues. Power configuration: 12 V DC power supply through a long cable. 12 V to 5 V DC-DC converter external (5 V / 3 A). (alibaba) AMS1117-3.3 regulator on pcb supplies the ESP32 and W5500. W5500 power controlled by a transistor/MOSFET circuit using ESP32 GPIO5, allowing the ESP32 to power-cycle the Ethernet module if it becomes unresponsive. W5500 CS connected to ESP32 GPIO0. Current problems: Sometimes the ESP32/w5500 fails to boot when power is first applied. I need to switch the 12 V supply OFF/ON several times before it starts. Sometimes the W5500 becomes unreachable even though its Ethernet LEDs are ON. I cannot determine whether the issue is related to power stability, ESP32 boot pins, W5500 initialization, or w5500. What I need: An experienced hardware/PCB engineer to review and improve my existing EasyEDA Pro project, particularly: ESP32 EN/reset and GPIO strapping pins. W5500 Ethernet connections and power-switching circuit. Capacitors, resistors, transistor/MOSFET selection, and PCB layout. Important: This is primarily a hardware design and troubleshooting project, not a firmware development project. The PCB is as industrial and must operate 24/7 unattended. The devices are installed remotely, so manually restarting them is not practical. I need a reliable design that starts correctly every time, withstands power interruptions, and supports automatic recovery if the Ethernet module fails. Deliverables: Identify the likely hardware root causes, recommend specific component/circuit changes, and update the existing EasyEDA Pro schematic and PCB layout. I can provide the complete EasyEDA Pro project, schematic, PCB files, firmware, and test measurements. before making offer tell me what u think problem is so based on this i can choose u coz now lot of people use chatgpt and i dont trust if u dont suggest first what u think is problem and what will u change
Project ID: 40826608
About the project
3 proposals
Open for bidding
Remote project
Active 22 secs ago
Place your bid
Bid amount Email addressBenefits of bidding on Freelancer
Set your budget and timeframe
It's free to sign up and bid on jobs
3 freelancers are bidding on average $23 USD for this job


Hello, The symptoms strongly suggest a power-sequencing and reset/strap problem rather than only a firmware issue. The long 12 V cable, external DC-DC converter, and AMS1117 supplying both ESP32 and W5500 can create startup dips, slow voltage rise, or noise during Ethernet activation. I would first examine the 3.3 V rail at power-up and during W5500 power cycling, the ESP32 EN/RESET network, GPIO0 strapping, and the GPIO5 transistor/MOSFET circuit. GPIO0 is also a boot-strapping pin, so its CS connection and external loading must be checked carefully. The W5500 may additionally require correct local decoupling, reset timing, SPI signal integrity, and a clean load-switch arrangement. With 10+ years in electronics, embedded systems, industrial hardware, schematic design, PCB layout, component selection, testing, and troubleshooting, I can review the complete EasyEDA Pro design at the circuit and layout level. I would specifically evaluate regulator headroom and transient response, bulk and high-frequency capacitors, pull-ups/pull-downs, MOSFET topology and gate states, grounding, Ethernet routing, and startup behavior, then update the schematic and PCB with practical component and layout changes for unattended operation. My initial recommendation is to verify the rails and boot pins with oscilloscope measurements before changing parts, so the root cause is identified rather than guessed. I can provide an engineering-based diagnosis a Thanks!


Hello, My first suspicion is a power-sequencing and boot-strap problem rather than an Ethernet software issue. The ESP32-WROOM-32 and W5500 share a 3.3 V rail generated by an AMS1117, while the external 5 V converter, long 12 V cable, startup transients, and switched W5500 supply can create undervoltage, slow ramp, ground-bounce, or backfeed conditions. GPIO0 is also a critical ESP32 strapping pin, so connecting it to W5500 CS without ensuring a defined level during reset may intermittently place the ESP32 in the wrong boot mode. I would also closely inspect EN/reset timing, pull-ups and capacitors, decoupling at both modules, the W5500 reset and power-discharge path, and whether GPIO5 can reliably control the transistor/MOSFET at startup. My proposed changes would be based on the actual EasyEDA schematic, layout, component values, and measurements: define safe ESP32 strap states, improve EN/reset supervision and power-on reset behavior, isolate or relocate W5500 CS if necessary, verify the MOSFET/transistor circuit prevents leakage and backfeed, add appropriate bulk and high-frequency decoupling, and review the 3.3 V regulator’s thermal, transient, and current margins. I would then update the schematic and PCB layout for reliable unattended operation, including clean W5500 power cycling and recovery support. I have over 15 years of electronic hardware and firmware engineering experience, including ESP32, SPI, Ethernet, industrial Thanks!
内容来自 Freelancer News,版权归原作者所有。
阅读原文 ↗