All-in-One Network Appliance Development
₹75000-150000 INR
Posted 1 minute ago
•
Ends in 6 days
₹75000-150000 INR
Paid on delivery
I need a single, integrated network appliance designed and prototyped from the ground up—hardware and software together. The unit must combine three core capabilities: firewall and network-level security, fully managed switching with access-point control, and 4G/5G dual-SIM internet bonding with automatic fail-over. Scope • Hardware: board-level design (schematic, PCB, component selection), metal or molded enclosure, thermal and power management, and at least one assembled, working prototype for bench testing. • Software: embedded OS image (OpenWrt, VyOS, or a comparable Linux build), drivers for the switch chip and cellular modems, an intuitive web/REST configuration interface, and field-upgradeable firmware. Acceptance criteria 1. Prototype boots reliably, passes throughput and fail-over tests, and sustains line-rate switching on all ports. 2. Firewall rules, VLANs, and AP provisioning are configurable via the UI without CLI access. 3. Dual-SIM bonding aggregates bandwidth and drops back to single-link seamlessly on loss of signal. 4. Full manufacturing package delivered: Gerbers, BOM, 3D enclosure files, compiled firmware, and source. If you already work with network SoCs such as Marvell, Qualcomm, or MediaTek and can take a concept from design to a tested prototype, let’s discuss timelines and milestones.
Project ID: 40824819
About the project
4 proposals
Open for bidding
Remote project
Active 13 secs ago
Place your bid
Bid amount Email addressBenefits of bidding on Freelancer
Set your budget and timeframe
It's free to sign up and bid on jobs
4 freelancers are bidding on average ₹101,335 INR for this job


Hello, This is a full-stack networking project where the trickiest part will be the 4G/5G bonding, getting the failover smooth enough to avoid dropping sessions while juggling dual SIMs. The enclosure and thermal design will also need testing early since it's handling cellular modems and a switch chip in one box. I'd start with the board schematic, picking an SoC that balances throughput and driver support (Marvell or MediaTek for cost, Qualcomm if you need higher-end). Then prototype the bonding logic first since that's the make-or-break feature, I'd test with a dev board and modems before finalizing the PCB. The UI can be OpenWrt-based to save time, extending LuCI or building a React frontend if you need more polish. Recently did a similar prototype for a failover router using MediaTek's MT7621, though without the switching layer. How locked in are you on the enclosure material? Metal's easier for thermal management but adds weight, have you ruled out high-temp plastic?


==== Hi - Quy Dao here ==== "HARDWARE AND SOFTWARE TOGETHER" - I will develop the appliance as an integrated, testable hardware and embedded-software prototype. I’ll first confirm the performance targets and select a compatible SoC, switch, and cellular modules. Then I’ll produce the schematic, PCB and enclosure designs, assemble a prototype, and build an OpenWrt- or comparable Linux-based image with firewall, VLAN, AP management, dual-SIM bonding/fail-over, configuration UI, and field-upgrade support. I’ll test boot reliability, switching and firewall throughput, UI-based configuration, SIM fail-over, and firmware upgrades against agreed acceptance criteria. Deliverables will include the tested prototype, Gerbers, BOM, enclosure files, compiled firmware, and source. A realistic schedule and milestones can be set once the component choices and performance targets are confirmed. Looking forward to work with you.


❤️❤️❤️Hi, I respect your benefit and do my best!❤️❤️❤️ ⭐⭐⭐⭐⭐⭐ I can take your integrated network appliance from concept to a tested prototype, combining firewall, managed switching with AP control, and dual-SIM 4G/5G bonding with failover. ✔ Board-level hardware design: schematic, PCB, component selection, enclosure, thermal and power management ✔ Embedded OS image on OpenWrt, VyOS or comparable Linux, with switch chip and cellular modem drivers ✔ Intuitive web and REST configuration interface for firewall rules, VLANs and AP provisioning without CLI ✔ Dual-SIM bonding aggregating bandwidth, with seamless fallback to single link on signal loss ✔ Field-upgradeable firmware and throughput, failover and line-rate switching validation ✔ Full manufacturing package: Gerbers, BOM, 3D enclosure files, compiled firmware and source ✔ Clean, well-documented work with clear communication throughout Experience with network SoCs such as Marvell, Qualcomm or MediaTek is available on request. This scope spans hardware and embedded engineering, so I would want to confirm whether you need a single partner or a coordinated team. Could you share the target throughput, port count and enclosure constraints, so I confirm the architecture and milestones? Best regards.
内容来自 Freelancer News,版权归原作者所有。
阅读原文 ↗