Revise an ESP32 battery-monitor PCB (KiCad), update firmware, build and test 5 samples
₹4000-7000 INR
Posted 1 minute ago
•
Ends in 6 days
₹4000-7000 INR
Paid on delivery
The budget specified on freelancer is our final budget. Please make sure your prices are final. The brief should be enough for any skilled candidate to bid correctly. BID increase will be disqualified What exists today: A working 2-board system. A transmitter (ESP32-C3) sits on a lithium battery pack and reads cell voltages. It sends them over ESP-NOW to a receiver (ESP32-C3 with a 2.8" ILI9341 display). Full KiCad projects and firmware for both boards are provided. The transmitter needs a small revision. The receiver may need a minor change. Battery: 4S, 5S or 6S lithium packs, 16.8V maximum. The battery is plugged in and unplugged in normal use. 1. Transmitter PCB changes • Add input protection before the buck converter (XL1509, 40V max): TVS (SMBJ20A or similar), input filtering, reverse-polarity protection. A 750mA fuse is already on the board. • Add a 2-pin connector for a 10k 1% B3950 NTC temperature sensor (the sensor sits inside the battery), read on a spare ADS1115 input. • Keep the JST battery connector. Move the USB connector 5mm outward. • Make sure the ON and OFF relay outputs (1-second pulse, 12V, up to 5A) can be driven by firmware. • Fix known issues: pick-and-place rotations, and the EN/IO9 issue on the current board. 2. Receiver check • The receiver needs two push buttons (ON and OFF) on ESP32 pins. Check the current design. If they’re not on pins, make the minimum change needed. 3. Firmware • Transmitter: read the NTC; fan relay on at 40°C, off at 38°C; cell count setting (4S/5S/6S); two calibration profiles (per cell 1.8–2.8V and 2.5–4.2V; two-point calibration already exists); simple pairing so the receiver address isn’t hard-coded; remove the Wi-Fi/OTA code. • Receiver: run the existing UI on the real display with live data, including temperature. • ON/OFF buttons: hardware test only for now (button press → relay pulse). Full logic comes later 4. Samples and testing • Build and test 5 sample sets. • Test on video: plug/unplug the battery 20 times at 16.8V with no damage; cell voltages within ±0.01V of a multimeter; temperature reading and fan switching; both relays and both buttons; both receiver screens with live data. Deliverables: updated KiCad projects, Gerbers, BOM (LCSC parts), pick-and-place, schematic PDF, firmware source for both boards, updated calibration steps. Payment: 3 milestones, each released on delivery: (1) schematic and layout changes reviewed, (2) production files accepted by the PCB maker, (3) samples tested with video, plus final firmware. Anything not listed here is extra and must be agreed in writing before work starts. Please quote: • A. Fixed price for design + firmware + testing (items 1–4) • B. Sample build (parts + PCB + assembly), price per transmitter and per receiver • C. Optional, price separately: RGB status LED output on the transmitter; remote 12V turn-on input • D. Timeline for each milestone
Project ID: 40823784
About the project
5 proposals
Open for bidding
Remote project
Active 29 secs ago
Place your bid
Bid amount Email addressBenefits of bidding on Freelancer
Set your budget and timeframe
It's free to sign up and bid on jobs
5 freelancers are bidding on average ₹5,300 INR for this job


My embedded-systems and PCB experience spans ESP32 development, sensor integration, I2C interfaces, relay control, circuit design, and PCB layout—an end-to-end match for revising your existing battery-monitor system rather than treating the hardware and firmware separately. I can work from the supplied KiCad projects to implement the transmitter protection, NTC input, connector and placement corrections, relay-driving requirements, and EN/IO9 fix, while checking the receiver button pin assignments. My ESP32, electronics, microcontroller, and hardware/software integration skills also align with updating the firmware for temperature/fan thresholds, 4S/5S/6S selection, calibration profiles, pairing, live ILI9341 data, and button-to-relay pulse testing. I will provide the requested KiCad production files, firmware source, calibration documentation, and testing deliverables. Any sample-build pricing and optional features would be quoted separately and kept within the stated final-budget requirement. I am ready to take responsibility for the complete design, firmware, and validation scope and would be pleased to deliver a reliable, testable revision of both boards.


I have experience with ESP32, PCB design, and firmware development. I have worked on similar hardware projects and can help you with your ESP battery monitor PCB revisions. You can check my experience by looking at my previous projects. I can also share project photos to show my work. I have an in-house lab for testing. Here's what I bring to this: → Built a solar RFID water vending machine on ESP32 with fully offline firmware, live in Mier, South Africa → Designed custom PCBs with TVS, reverse-polarity and input filtering for field-deployed battery hardware → Full stack in-house: KiCad schematic/layout, C/C++ firmware, pick-and-place fixes, BOM with LCSC parts My approach: → Review both KiCad projects, confirm the receiver button pins, then send you schematic changes for sign-off → Do the transmitter revision and firmware (NTC fan hysteresis, cell count, pairing, Wi-Fi removed), then receiver UI with live data → Build and test 5 sets, record the 20x 16.8V plug/unplug and multimeter checks on video, hand over Gerbers, BOM, source and calibration steps


My Microcontroller, PCB Layout, and Electrical Engineering skills align directly with revising this ESP32 battery-monitor system, including the KiCad transmitter changes, receiver button checks, firmware updates, and sample testing requirements. I can work on the provided PCB designs and firmware with attention to the requested protection circuitry, NTC input, relay outputs, ESP32 pin assignments, calibration profiles, cell-count settings, ESP-NOW pairing, and live receiver display data. My microcontroller background is relevant to implementing and validating the temperature, fan, relay, button, and battery-monitor functions, while my PCB layout skills support the connector relocation, EN/IO9 correction, pick-and-place updates, Gerbers, BOM, and schematic documentation. I will provide a fixed-price quotation for A, per-board sample pricing for B, separate optional pricing for C, and milestone timelines for D without increasing the agreed budget. I would be glad to take responsibility for the complete design, firmware, documentation, and five-sample testing package.
内容来自 Freelancer News,版权归原作者所有。
阅读原文 ↗