KiCad ECO: 24V 8-Port LED Driver Boards v0.2 to v0.3

$30-250 USD

$30-250 USD

Paid on delivery

Hardware revision of an existing KiCad design: Farmicca Illuminator Main Module and Extender, from v0.2 to v0.3. The v0.2 boards have five confirmed failure modes. Correct them in schematic and PCB. Keep the rest of the architecture. Failures to fix 1. 5-pin port silkscreen (J4–J11): Pin 2 is marked GND but is the +24 V common anode. Relabel Pin 2 as +24V and add the legend [1: NTC | 2: +24V | 3: CH1 | 4: CH2 | 5: CH3] plus a port number beside each connector. 2. Voltage drop: 0.1 ohm high-side shunt per port (~0.30 V and ~0.90 W at 3 A in an 0805) and 0.1 ohm low-side shunt per channel. Remove both. MOSFET sources go straight to PGND. Per-port shunt amplifiers and their passives come out of the schematic. Tie off or repurpose the old multiplexer inputs so they do not float. 3. Channel MOSFET overheating: 1 kΩ + 0.1 µF gate filter (τ ≈ 100 µs) holds the FET in the linear region, and the SOT-23 package cannot shed the heat (~0.45 W conduction, ~+99 °C rise). Remove the gate capacitors. Use 10–22 Ω gate resistors. Replace the FETs with a thermally enhanced package (SO-8 / PowerPAK SO-8 / LFPAK56 / DFN5060-8 class), exposed pad stitched to the plane, target RDS(on) 6–8 mΩ at the confirmed VGS, ID ≥ 30 A. Replace the overheating resistor-divider gate supply with a regulated gate-driver rail. 4. 27 V SOD-123 Zeners (500 mW) avalanche on the normal 24 V bus and burn. Remove the 27 V and 3.3 V Zeners. Size the clamp only after the exact connection (drain-source, drain-ground, or gate-source) is confirmed on the schematic. Flyback diodes move to 60 V parts. Input capacitors move to 50 V. 5. The 24 V distribution cannot carry 8 ports × 3 A = 24 A. Use 2 oz (70 µm) finished copper, +24 V and PGND planes, an 8–10 mm backbone on the 24 A path (verify with IPC-2152 for ~10 °C rise), and via stitching (0.3 mm drill, 0.6 mm pad, 4–6 vias) at power pins and FET drain/source. Check the connector pin rating against 3 A per port. Aggregate current stays on the existing input Hall-effect sensor (SYS_VOL / SYS_CUR). Confirm the exact measurement point before the schematic is frozen. Leave these unchanged - Overall architecture and schematic structure outside the driver and output areas - STM32 and ESP32 sections - NTC circuit - SYS_VOL / SYS_CUR - IL-SENSE / sensor connector J10 The new FET package does not fit the SOT-23 pads, so the driver and output areas are re-laid out. Confirm stack-up and copper weight with the fabricator before any order is placed. Proposed finish: matte black solder mask, white silkscreen (confirm the fab can print white on black). Board requirements to preserve - 8 output ports, 3 channels per port (CH1 / CH2 / CH3) - 3 A per port (see the open question below) - Correct 5-pin assignment - No series sense resistor left in the port or channel path Deliverables - Updated KiCad project for Main Module and Extender: schematics, symbols, footprints, PCB, target 0 ERC and 0 DRC, with the report in the final package - Gerber RS-274X, Excellon drill, board outline, centroid/CPL - BOM with lifecycle status and distributor part numbers. No final part numbers until the schematic update; submit the BOM for approval - Short engineering-change note: root causes, changes, power/thermal calculations, assumptions, ERC/DRC results - A written acceptance checklist for the prototype: port voltage drop, thermal rise, turn-off spikes, gate waveforms, reverse polarity, regression, optional emissions - One round of DFM comments with the chosen PCB fabricator Out of scope - Firmware changes (only a pin-map note for ADC channels that no longer read per-port shunts) - Manufacturing, assembly, shipping, and physical test cost - Claiming the design is validated. Prototypes are tested by the client. Performance is confirmed on hardware, not in this package. Answer these before layout freeze 1. Is 3 A the sum of CH1–CH3 on one port, or can a single channel carry 3 A? 2. PWM frequency, worst-case simultaneous load, and maximum ambient inside the enclosure (thermal math currently assumes 40 °C). 3. CH1/CH2/CH3 colour mapping and confirmation that Pin 2 is the +24 V pin. 4. Gate-drive rail voltage. The correction letter uses a regulated 12 V driver; RDS(on) must be specified at the real VGS. 5. Is aggregate current/voltage at the board input (existing Hall sensor) acceptable? 6. Exact Zener/TVS connection on the schematic before the clamp is sized. Existing KiCad schematic and PCB files will be supplied to the selected freelancer. Work starts after the six answers above and written approval of this change list.

Project ID: 40822728

About the project

9 proposals

Remote project

Active 13 mins ago

Looking to make some money?

Email address

Benefits of bidding on Freelancer

Set your budget and timeframe

It's free to sign up and bid on jobs

9 freelancers are bidding on average $152 USD for this job

User Avatar
Flag of TURKEY

Power electronics and power-board PCB design make this KiCad ECO closely aligned with my background. I have designed AC/DC and DC/DC converters, battery chargers, solar inverters, UPS systems, motor drives, and power boards, giving me relevant experience with high-current paths, switching devices, thermal considerations, and regulated power circuitry. My circuit-design and PCB-layout skills cover schematic development, power PCB design, SMPS boards, manufacturer CAD files, and hardware simulation using OrCAD and MATLAB. I can apply that experience to the driver/output redesign while preserving the STM32, ESP32, NTC, Hall-sensor, and existing architecture sections. I will also prepare the revised schematics and PCB, ERC/DRC reports, manufacturing outputs, BOM, engineering-change note, and prototype acceptance checklist specified for the v0.3 package. I understand that the design must distinguish assumptions from hardware validation and that the final FET, clamp, copper, connector, and thermal choices depend on confirmed operating conditions and fabricator constraints. My embedded experience with STM32, ESP32, PIC, dsPIC, DSP, and other controllers also supports the required ADC pin-map note. Choose me to carry out this power-focused KiCad revision with careful electrical and layout review.

User Avatar
Flag of JORDAN

Hello, I’m a Top Rated engineer with 15+ years in embedded systems, PCB design and industrial electronics. Your change list is well defined, so my focus would be getting the revision right the first time: FET and gate-drive selection verified at the real VGS, a clamp sized only after the connection is confirmed, and a 24 A copper path checked against IPC-2152 and your fab’s stack-up. Deliverables as listed: KiCad project at 0 ERC/DRC, Gerbers, CPL, BOM for approval, change note, acceptance checklist and one DFM round. Price: $90 fixed | 3-7 days after your six answers | 1 revision. Is the 3 A per port or per channel? It decides the FET and copper sizing. Best regards, Hamza

User Avatar
Flag of INDIA

PCB layout and circuit design are directly aligned with this KiCad hardware revision, including reworking the driver and output areas while preserving the STM32, ESP32, NTC, and aggregate sensing sections. My skills in Circuit Design, Embedded Systems, and PCB Layout support the required schematic and board changes: removing the series shunts, updating MOSFET footprints and gate networks, routing high-current +24 V and PGND planes, and preparing the revised Main Module and Extender layouts. I can also produce the associated fabrication outputs, BOM, and design documentation, including ERC/DRC reports and engineering-change notes. I will keep the design changes within the stated scope and avoid claiming prototype validation before hardware testing. I would be glad to take responsibility for this v0.2-to-v0.3 KiCad revision and deliver a clean, fabrication-ready package for your review.

User Avatar
Flag of INDIA

Circuit design, electrical engineering, and PCB layout are directly aligned with this KiCad hardware revision, particularly the required schematic corrections and re-layout of the driver/output areas. I can work on the Main Module and Extender while preserving the STM32, ESP32, NTC, SYS_VOL/SYS_CUR, and IL-SENSE sections, and focus the revision on eliminating the series shunts, correcting port labeling, upgrading the MOSFET implementation, and improving the 24 V/PGND distribution. My PCB layout experience supports the high-current requirements, including power planes, copper routing, via stitching, thermal considerations, connector checks, and design-rule review. I can prepare the updated schematics and PCB files together with Gerbers, drill files, CPL, BOM for approval, ERC/DRC reports, engineering-change documentation, and the prototype acceptance checklist. I will also keep the design assumptions explicit, including the confirmed measurement point, channel/port current interpretation, PWM and thermal conditions, stack-up, and copper weight before layout freeze. I would be pleased to apply my circuit design and PCB layout skills to produce a clean, reviewable v0.3 package for your prototype stage.

User Avatar
Flag of BANGLADESH

I can take the existing KiCad Main Module and Extender from v0.2 to v0.3 while preserving the overall architecture and making the specified driver, protection, power-distribution, and thermal corrections properly in both schematic and PCB. I have 13+ years of experience in PCB design, embedded electronics, power electronics, schematic capture, thermal/power analysis, and manufacturing-ready PCB documentation. I’ll remove the unnecessary shunts, redesign the MOSFET driver/output areas for the new thermally enhanced packages, implement the regulated gate-drive rail, update protection components, and rebuild the 24 V/PGND distribution using the required copper weight, planes, backbone, and via stitching. I’ll also correct J4–J11 pin legends, verify connector ratings, preserve the STM32/ESP32, NTC, SYS_VOL/SYS_CUR and IL-SENSE sections, and avoid firmware changes except the required ADC pin-map note. Before layout freeze, I’ll explicitly resolve the six listed questions and document all assumptions. I’ll target 0 ERC / 0 DRC and provide the editable KiCad project, Gerbers, Excellon, CPL, BOM, engineering-change note, calculations, acceptance checklist, and one DFM review. I’ll also verify the exact Zener/TVS connection before selecting the final clamp and confirm the MOSFET RDS(on) at the actual gate-drive voltage. The final package will clearly distinguish calculated design verification from hardware validation, which remains with the prototype test process.

User Avatar
Flag of UNITED STATES

Hi, The main challenge is correcting the power distribution and MOSFET thermal issues without disturbing the existing architecture or critical STM32, ESP32, and sensor circuits. I would approach this as a controlled hardware revision, first reviewing the existing KiCad schematics and PCB against all five failure modes. I would remove the unnecessary current-sense resistors, redesign the MOSFET driver and output stages with suitable low-RDS(on) power packages, and rebuild the 24 V and PGND distribution with properly calculated copper widths, planes, and via stitching. I would also verify voltage ratings, protection circuitry, gate-drive requirements, and connector current capacity before finalizing the layout. Both boards would be checked for ERC and DRC compliance, with supporting electrical and thermal calculations. You will receive the complete KiCad projects, manufacturing files, BOM, engineering-change documentation, and prototype acceptance checklist. I would preserve the existing architecture and clearly document all assumptions before layout freeze.

User Avatar
Flag of TURKEY

Hi there, I see that you require a revision of the KiCad design for the Farmicca Illuminator, addressing critical failure modes while retaining the overall architecture. I can assist in correcting the five specified issues, such as updating the silkscreen labels and removing unnecessary components to prevent component overheating and voltage drops. I will also ensure that the new FET package is appropriately laid out to match the thermal requirements and confirm the PCB specifications with the fabricator. In addition, I’ll draft the necessary documentation, including the revised schematics, BOM, and an engineering change note detailing the root causes and updates. To clear a few things up prior to finalizing the design, could you clarify if the 3 A specification is the maximum for a single channel or the total per port? Also, what is your expected PWM frequency and maximum ambient temperature for this project? Let’s ensure everything is aligned before locking in the schematic. Regards, Ali

User Avatar
Flag of TURKEY

Merhaba, beş arıza modunu okudum, teşhisleriniz doğru ve revizyonu KiCad'de iki kart için (Main + Extender) yapabilirim. Planım kısaca: 1. Silkscreen: J4-J11 pin 2 = +24V, legend [1: NTC | 2: +24V | 3: CH1 | 4: CH2 | 5: CH3] ve port numarası. 2. Şönt ve şönt amplifikatörleri şemadan çıkar, kaynaklar doğrudan PGND; boşta kalan mux girişleri GND'ye bağlanır ya da ayrı test noktasına alınır, firmware tarafına hangi kanalın boşa çıktığı listesi verilir. 3. Kapı: kondansatör çıkar, 10-22 Ω seri direnç, LFPAK56 / PowerPAK SO-8 sınıfı FET (RDS(on) 6-8 mΩ, onaylanan VGS'de), açık ped termal via dikişli; direnç bölücü yerine regüleli kapı sürücü rayı (24 V'tan küçük bir LDO/buck ile 10-12 V). 4. 27 V ve 3,3 V zenerler çıkar; kelepçe ancak bağlantı noktası şemada teyit edilince boyutlanır (24 V bus toleransına göre TVS). Flyback 60 V, giriş kondansatörleri 50 V. 5. 2 oz bakır, +24V ve PGND düzlemleri, 24 A ana hat IPC-2152 ile ~10 °C artışa göre genişlik, güç pinlerinde ve FET drain/source'ta via dikişi; konnektör pin akımı port başına 3 A'ya karşı kontrol. STM32, ESP32, NTC, SYS_VOL/SYS_CUR ve J10'a dokunulmaz. Teslimde: güncel KiCad projesi, ERC/DRC temiz rapor, değişiklik listesi (ECO), Gerber + BOM + CPL ve fabrikaya gidecek stack-up notu. Bu revizyon iki kartta sürücü ve çıkış bölgesinin yeniden yerleşimi demek, bu yüzden bütçe üstü bir teklif veriyorum; iş kilometre taşlarına bölünebilir (önce şema ECO, onayınızdan sonra layout). Tek sorum: kanalları şu an hangi PWM frekansıyla sürüyorsunuz ve kapılar doğrudan MCU pininden mi geliyor? Kapı sürücü seçimi buna bağlı.

内容来自 Freelancer News,版权归原作者所有。

阅读原文 ↗

把喜欢的内容,留在你的新标签页。

打开我的订阅