Smart Anti-Shock Bracelet Prototype

$15-25 USD / hour

Posted 1 minute ago

•

Ends in 6 days

$15-25 USD / hour

I’m developing a slim, battery-powered bracelet that can sense dangerous electrical fields without direct contact and, the instant it recognizes an unsafe voltage, respond with a loud buzzer and a bright flash. To move from concept to a wrist-ready prototype I’m looking for end-to-end support—firmware, hardware, and proof-of-concept assembly all wrapped into one project. Here’s what the work entails: • Microcontroller & Firmware Write low-power, watchdog-protected C/C++ on an STM32 or ESP32, with deep-sleep modes that keep standby draw under 1 mA and a wake-to-alert time below 200 ms. • Hardware & PCB Produce a compact, multilayer PCB and full schematic tailored to a wearable form factor. Factor in a non-contact electric-field sensor, Li-ion charging IC, over-current protection, and connectors for a piezo buzzer and high-intensity LED. • Sensor Integration Select, integrate, and calibrate the electric-field sensor so the bracelet can detect 110–240 V mains from roughly 5 cm away, ignoring normal environmental noise. • Power Management Design the power path and optimize firmware to deliver multiple days of use on a small cell, with accurate battery gauging and USB-based charging. • Safety & Reliability Incorporate surge suppression, isolation, fail-safe logic, and documented test procedures that prove the bracelet remains safe even under fault conditions. Expected deliverables: — Block diagram and initial BoM — Production-ready schematic and Gerber files — Fully commented firmware source with build guide — 3D enclosure files sized for a wristband — One assembled, tested prototype shipped to me — A concise engineering report (sensor calibration data, power budget, validation results) I’ll consider the job complete once the prototype consistently senses live mains, sounds the buzzer and flashes the LED, logs zero missed events over 1,000 trials, and meets the standby current spec. If you can drive this through to a polished, field-tested bracelet, let’s discuss timelines and milestones.

Project ID: 40822222

About the project

5 proposals

Open for bidding

Remote project

Active 4 secs ago

Place your bid

Bid amount Email address

Benefits of bidding on Freelancer

Set your budget and timeframe

It's free to sign up and bid on jobs

5 freelancers are bidding on average $20 USD/hour for this job

User Avatar
Flag of UKRAINE

Hello, Designing a wearable safety device that combines sensing, embedded control, power management, and a compact PCB is directly aligned with my 15+ years as an Electronic Hardware and Firmware Engineer. I have developed embedded systems around STM32, ESP32, and ARM Cortex platforms using C/C++, alongside complex PCB designs in Altium Designer, KiCad, and Eagle. My experience covers the core requirements of this bracelet: low-power firmware, watchdog protection, sensor integration, Li-ion power paths, and reliable hardware for consumer, medical, automotive, and industrial applications. I can provide the schematic, PCB layout, firmware source, simulation support through LTspice or MATLAB/Simulink, and the engineering documentation needed to evaluate calibration, power consumption, and fault behavior. I am well suited to drive this project from concept through proof-of-concept assembly, with careful attention to isolation, surge protection, fail-safe operation, and wearable form-factor constraints. Choose me to develop a disciplined hardware-and-firmware foundation for your anti-shock bracelet and bring the prototype toward validation. Thanks!

User Avatar
Flag of UKRAINE

Hello, Developing a wrist-ready safety device requires both embedded expertise and practical hardware engineering, and I offer 10+ years of experience taking electronic products from concept through schematic, multilayer PCB design, prototyping, testing, troubleshooting, and manufacturing documentation. My background directly matches your STM32/ESP32 firmware, low-power electronics, sensor integration, power management, and compact PCB requirements. I can support the complete design across analog and digital electronics, ADC-based sensors, component selection, protection circuits, Li-ion power systems, USB charging, watchdog operation, buzzer/LED control, and hardware-firmware integration. My 3D CAD, 3D modeling, 3D printing, and rapid-prototyping experience also supports the wristband enclosure and assembled proof-of-concept. I will approach the mains-field detection and isolation requirements with the safety focus expected of an industrial electronics engineer, including documented testing, calibration, power measurements, fault checks, and prototype validation. I am ready to take responsibility for the complete engineering package and deliver a polished, testable bracelet prototype. Thanks!

User Avatar
Flag of UKRAINE

Hello, Turning an electronics concept into a prototype-ready product is my core work, covering embedded firmware, circuit design, PCB layout, component selection, Gerbers, BOMs, testing, and engineering documentation. Your wearable anti-shock bracelet aligns especially well with my experience in embedded systems, low-power IoT and wearable devices. I work with STM32 and ESP32 using embedded C/C++, and can develop the watchdog-protected firmware, power-conscious operating modes, sensor integration, buzzer/LED alert control, and charging and protection circuitry required for this design. My PCB experience includes compact 1-8 layer boards using Altium Designer, KiCad, Eagle, and EasyEDA, along with custom footprints, BOM validation, manufacturing files, hardware prototyping, and testing. I can also support the 3D enclosure design, schematic and Gerber generation, firmware build documentation, sensor calibration records, power budgeting, and validation report. My electronics, microcontroller, embedded-systems, and PCB-layout skills make me well suited to take this bracelet from concept toward a wrist-ready proof of concept. Choose me to develop the hardware and firmware as one integrated prototype. Thanks!

User Avatar
Flag of UKRAINE

My embedded-systems and firmware skills align directly with this bracelet prototype, particularly C programming, microcontroller development, electronics, and firmware engineering. I can support the core proof of concept across the sensing, alert, and low-power control requirements using an STM32 or ESP32-based design. My background also includes PLC, SCADA, and Industrial IoT solutions, giving me relevant experience with hardware-driven systems and safety-focused applications. I can contribute to the firmware source, watchdog and power-management logic, sensor integration, buzzer/LED control, and supporting technical documentation. My broader software and engineering experience enables end-to-end coordination between embedded code, connected systems, and a practical wearable prototype. I am ready to take ownership of this challenging anti-shock bracelet project and deliver a focused, testable proof of concept with clear engineering documentation.

内容来自 Freelancer News,版权归原作者所有。

阅读原文 ↗

把喜欢的内容,留在你的新标签页。

打开我的订阅